INPUT SHAFT > REASSEMBLY |
| 1. INSTALL FRONT INPUT SHAFT BEARING |
![]() |
Using a press, press the front input shaft bearing onto the input shaft.
| 2. INSTALL 3RD GEAR NEEDLE ROLLER BEARING |
![]() |
Coat the 2 pieces of the 3rd gear needle roller bearing with gear oil and install them to the input shaft.
| 3. INSTALL 3RD GEAR SUB-ASSEMBLY |
![]() |
Coat the 3rd gear with gear oil and install it to the input shaft.
| 4. INSTALL NO. 3 SYNCHRONIZER RING |
![]() |
Coat the No. 3 synchronizer ring with gear oil and install it to the 3rd gear.
| 5. INSTALL NO. 2 TRANSMISSION CLUTCH HUB |
Coat the No. 2 transmission clutch hub with gear oil.
![]() |
Using SST and a press, press the No. 2 transmission clutch hub to the input shaft.
| 6. INSTALL NO. 2 CLUTCH HUB SETTING SHAFT SNAP RING |
Select a new snap ring that will allow minimal axial play.
| Mark | Specified Condition | Mark | Specified Condition |
| 0 | 2.30 mm (0.0905 in.) | 3 | 2.48 mm (0.0976 in.) |
| 1 | 2.36 mm (0.0929 in.) | 4 | 2.54 mm (0.0999 in.) |
| 2 | 2.42 mm (0.0952 in.) | 5 | 2.60 mm (0.1023 in.) |
![]() |
Using a snap ring expander, install the No. 2 clutch hub setting shaft snap ring.
| 7. INSTALL SYNCHROMESH SHIFTING KEY |
![]() |
Install the 3 synchromesh shifting keys to the No. 2 transmission clutch hub.
| 8. INSTALL NO. 2 TRANSMISSION HUB SLEEVE |
Coat the No. 2 transmission hub sleeve with gear oil.
Install the No. 2 transmission hub sleeve to the No. 2 transmission clutch hub.
| 9. INSTALL 4TH GEAR BEARING SPACER |
![]() |
Install the 4th gear bearing spacer to the input shaft.
| 10. INSTALL NO. 4 SYNCHRONIZER RING |
![]() |
Coat the 4th gear needle roller bearing and 4th gear bearing spacer with gear oil and install the 4th gear needle roller bearing to the input shaft.
![]() |
Coat the No. 4 synchronizer ring with gear oil and install it to the No. 2 transmission clutch hub.
| 11. INSTALL 4TH GEAR SUB-ASSEMBLY |
![]() |
Coat the 4th gear with gear oil and install it to the input shaft.
| 12. INSTALL INNER 5TH GEAR BEARING RACE LOCK BALL |
![]() |
Coat the inner 5th gear bearing race lock ball with gear oil and install it to the input shaft.
| 13. INSTALL INNER 5TH GEAR BEARING RACE |
![]() |
Coat the inner 5th gear bearing race with gear oil and install it to the input shaft.
| 14. INSTALL 5TH GEAR NEEDLE ROLLER BEARING |
![]() |
Coat the 2 pieces of the 5th gear needle roller bearing and inner 5th gear bearing race with gear oil and install the 5th gear needle roller bearing to the input shaft.
| 15. INSTALL 5TH GEAR |
![]() |
Coat the 5th gear with gear oil and install it to the input shaft.
| 16. INSTALL NO. 5 SYNCHRONIZER RING |
![]() |
Coat the No. 5 synchronizer ring with gear oil and install it to the 5th gear.
| 17. INSTALL NO. 3 TRANSMISSION CLUTCH HUB |
Coat the No. 3 transmission clutch hub with gear oil.
![]() |
Using SST and a press, press the No. 3 transmission clutch hub onto the input shaft.
| 18. INSTALL SYNCHROMESH SHIFTING KEY |
![]() |
Install the 3 synchromesh shifting keys to the No. 3 transmission clutch hub.
| 19. INSTALL INNER 6TH GEAR BEARING RACE LOCK BALL |
![]() |
Coat the inner 6th gear bearing race lock ball with gear oil and install it to the input shaft.
| 20. INSTALL NO. 3 TRANSMISSION HUB SLEEVE |
Coat the No. 3 transmission hub sleeve with gear oil.
![]() |
Install the No. 3 transmission hub sleeve to the No. 3 transmission clutch hub.
| 21. INSTALL INNER 6TH GEAR BEARING RACE |
![]() |
Coat the inner 6th gear bearing race with gear oil and install it to the input shaft.
| 22. INSTALL 6TH GEAR NEEDLE ROLLER BEARING |
![]() |
Coat the 2 pieces of the 6th gear needle roller bearing and inner 6th gear bearing race with gear oil and install the 6th gear needle roller bearing to the input shaft.
| 23. INSTALL NO. 5 SYNCHRONIZER RING |
![]() |
Coat the No. 5 synchronizer ring with gear oil and install it to the No. 3 transmission clutch hub.
| 24. INSTALL 6TH GEAR |
![]() |
Coat the 6th gear with gear oil and install it to the input shaft.
| 25. INSTALL REAR INPUT SHAFT RADIAL BALL BEARING |
![]() |
Using SST and a press, press the rear input shaft radial ball bearing onto the input shaft.
| 26. INSTALL REAR INPUT SHAFT BEARING SHAFT SNAP RING |
Select a new snap ring that will allow minimal axial play.
| Mark | Specified Condition | Mark | Specified Condition |
| 0 | 1.90 mm (0.0748 in.) | 6 | 2.26 mm (0.0889 in.) |
| 1 | 1.96 mm (0.0771 in.) | 7 | 2.32 mm (0.0913 in.) |
| 2 | 2.02 mm (0.0795 in.) | 8 | 2.38 mm (0.0937 in.) |
| 3 | 2.08 mm (0.0818 in.) | 9 | 2.44 mm (0.0960 in.) |
| 4 | 2.14 mm (0.0842 in.) | A | 2.50 mm (0.0984 in.) |
| 5 | 2.20 mm (0.0866 in.) | - | - |
![]() |
Using a snap ring expander, install the rear input shaft bearing shaft snap ring.
| 27. INSPECT 3RD GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 3rd gear radial clearance.
| 28. INSPECT 4TH GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 4th gear radial clearance between the gear and shaft.
| 29. INSPECT 5TH GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 5th gear radial clearance between the gear and shaft.
| 30. INSPECT 6TH GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 6th gear radial clearance between the gear and shaft.
| 31. INSPECT 3RD GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the 3rd gear thrust clearance.
| 32. INSPECT 4TH GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the 4th gear thrust clearance.
| 33. INSPECT 5TH GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the 5th gear thrust clearance.
| 34. INSPECT 6TH GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the 6th gear thrust clearance.