Home › TRANSMISSION ยท EB61 MANUAL TRANSAXLE › MANUAL TRANSAXLE UNIT

MANUAL TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE MANUAL TRANSMISSION FILLER PLUG


    C199064
  1. Remove the filler plug and gasket from the manual transmission case.



2. REMOVE MANUAL TRANSMISSION DRAIN PLUG


    C199063
  1. Remove the drain plug and gasket from the front transaxle case.



3. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY


    C199065
  1. Using a 27 mm deep socket wrench, remove the back-up light switch and gasket from the manual transmission case.



4. REMOVE TRANSMISSION CASE PLUG


    C206934
  1. Remove the transmission case plug and gasket from the manual transmission case.



5. REMOVE CONTROL CABLE BRACKET ASSEMBLY


    C199067
  1. Remove the 3 bolts and control cable bracket from the manual transmission case.



6. REMOVE RELEASE CYLINDER BLEEDER PLUG CAP
  1. Remove the bleeder plug cap from the release cylinder bleeder plug.



7. REMOVE RELEASE CYLINDER BLEEDER PLUG
  1. Remove the bleeder plug from the clutch release bleeder sub-assembly.



8. REMOVE CLUTCH CLUTCH RELEASE CYLINDER TO BLEEDER TUBE


9. REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY


C199329
  1. Using a union nut wrench, separate the clutch release bleeder sub-assembly from the clutch release cylinder to bleeder tube.

  1. Remove the 2 bolts and clutch release bleeder sub-assembly from the manual transaxle assembly.



10. REMOVE CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY


    C199330
  1. Remove the clutch tube boot from the manual transaxle assembly.



    C199331
  1. Remove the 3 bolts and clutch release with bearing cylinder assembly and clutch release cylinder to bleeder tube.



    C199287
  1. Using a union nut wrench, remove the clutch release cylinder to bleeder tube from the clutch release with bearing cylinder assembly.



11. SECURE MANUAL TRANSAXLE ASSEMBLY


    C199068
  1. Place the manual transaxle on wooden blocks.



12. REMOVE REVERSE IDLER GEAR SHAFT BOLT


    C199070
  1. Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.



13. REMOVE LOCK BALL PIN


    C199071
  1. Using a 10 mm hexagon socket wrench, remove the plug from the manual transmission case.

  1. Using a magnet hand, remove the compression spring and lock ball pin from the manual transmission case.



    C199069
  1. Using a 10 mm hexagon socket wrench, remove the plug from the manual transmission case.

  1. Using a magnet hand, remove the compression spring and lock ball pin from the manual transmission case.



14. REMOVE SHIFT DETENT BALL


    C199072
  1. Using a 6 mm hexagon socket wrench, remove the shift detent ball plug from the manual transmission case.

  1. Using a magnet hand, remove the compression spring and shift detent ball from the manual transmission case.



    C199073
  1. Using a 6 mm hexagon socket wrench, remove the 2 shift detent ball plugs from the manual transmission case.

  1. Using a magnet hand, remove the 2 compression springs and 2 shift detent balls from the manual transmission case.



15. REMOVE OUTER SHIFT LEVER E-RING


    C199074
  1. Remove the E-ring from the outer No. 1 shift lever.



16. REMOVE MANUAL TRANSMISSION CASE


    C199075
  1. Remove the 17 bolts.



    C202174E01
  1. Using a screwdriver with its tip wrapped with protective tape, separate the manual transmission case from the front transaxle case.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not damage the manual transmission case.



    C202175
  1. Turn the outer No. 1 shift lever clockwise until it comes into contact with the boss.



    C202176
  1. Push the outer No. 1 shift lever and remove the manual transmission case.



17. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY


    C202177
  1. Remove the reverse idler gear, thrust washer and reverse idler gear shaft from the front transaxle case.



18. REMOVE REVERSE SHIFT FORK SHAFT ASSEMBLY


    C202178
  1. Turn the reverse shift fork shaft clockwise and remove it from the front transaxle case.



19. REMOVE REVERSE SHIFT FORK


    C200913
  1. Using a 5 mm pin punch and hammer, tap out the reverse shift fork slotted spring pin.

  1. Remove the reverse shift fork from the reverse shift fork shaft.



20. REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY


    C202179
  1. Using a 6 mm hexagon socket wrench, remove the 2 bolts and reverse shift arm bracket from the front transaxle case.



21. REMOVE OUTER SELECT LEVER


    C202180
  1. Remove the inner select lever bolt.



    C203006
  1. Remove the outer select lever and inner select lever from the front transaxle case.



22. REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY


    C203070
  1. Turn the shift and select lever shaft clockwise and remove it from the front transaxle case.



23. REMOVE OUTER SELECT LEVER OIL SEAL


    C202195E01
  1. Using a screwdriver with its tip wrapped with protective tape, remove the outer select lever oil seal from the front transaxle case.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not damage the installation surfaces.



24. REMOVE INPUT SHAFT ASSEMBLY


    C202181
  1. Remove the input shaft assembly, output shaft assembly and 2 gear shift fork shaft assemblies from the front transaxle case.

  1. Remove the output shaft assembly together with the No. 1 gear shift fork shaft assembly from the input shaft assembly.

  1. Remove the No. 1 gear shift fork shaft assembly from the output shaft assembly.

  1. Remove the No. 2 gear shift fork shaft assemblies from the input shaft assembly.



25. REMOVE DIFFERENTIAL CASE ASSEMBLY


    C202182
  1. Remove the differential case from the front transaxle case.



26. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    C202183E01
  1. Using SST, remove the front differential case front tapered roller bearing (outer race) and front differential oil baffle from the front transaxle case.



    C199076E01
  1. Using SST, remove the differential case assembly front tapered roller bearing from the differential case assembly.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00350, 09951-00550, 09952-06010)
    Text in Illustration 
    *1
    Turn
    *2
    Hold



27. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


    C202184E01
  1. Using SST, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear shim from the manual transmission case.

    SST
    09308-00010  



    C199077E01
  1. Using SST, remove the front differential case rear tapered roller bearing from the front differential case assembly.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04021, 09957-04010, 09958-04011)
    09950-60010   (09951-00350, 09951-00550, 09952-06010)
    Text in Illustration 
    *1
    Turn
    *2
    Hold



28. REMOVE TRANSMISSION MAGNET


    C202185
  1. Remove the transmission magnet from the front transaxle case.



29. REMOVE BREATHER PLUG


    C202186
  1. Remove the breather plug from the front transaxle case.



30. REMOVE FRONT OUTPUT SHAFT BEARING


    C202187E01
  1. Using SST, tap the front output shaft bearing (outer race) from the front transaxle case.

    SST
    09308-00010  



    C202188
  1. Remove the output shaft cover from the front transaxle case.



31. REMOVE FRONT TRANSAXLE CASE OIL SEAL


    C202189E01
  1. Using SST, tap out the front transaxle case oil seal from the front transaxle case.

    SST
    09950-60010   (09951-00360)
    09950-70010   (09951-07150)



32. REMOVE STRAIGHT PIN


    C204734
  1. Remove the 5 straight pins from the front transaxle case.



33. REMOVE REAR INPUT SHAFT BEARING SHIM


    C202191
  1. Remove the rear input shaft bearing shim from the manual transmission case.



34. REMOVE INPUT SHAFT COVER


    C202192
  1. Remove the input shaft cover from the manual transmission case.



35. REMOVE NO. 1 OIL RECEIVER PIPE


    C202193
  1. Remove the No. 1 oil receiver pipe from the manual transmission case.



36. REMOVE OUTER NO. 1 SHIFT LEVER


    C202879
  1. Using a 5 mm pin punch and hammer, tap out the inner shift lever slotted spring pin.

    HINT:
    When removing the slotted spring pin, align the pin with the hole in the lock ball assembly.

  1. Remove the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever from the manual transmission case.



37. REMOVE OUTER SHIFT LEVER OIL SEAL


    C202195
  1. Using a screwdriver with its tip wrapped with protective tape, remove the outer shift lever oil seal from the front transaxle case.

    NOTICE:
    Do not damage the installation surfaces.



38. REMOVE REAR OUTPUT SHAFT BEARING


    C202196E01
  1. Using SST, remove the rear output shaft bearing (outer race) and rear output shaft bearing shim from the manual transmission case.

    SST
    09308-00010  



39. REMOVE TRANSMISSION CASE OIL SEAL


    C202197E01
  1. for LH side:

    1. Using SST, remove the transmission case oil seal from the manual transmission case.

      SST
      09308-00010  



    C202198E01
  1. for RH side:

    1. Using SST, remove the transmission case oil seal from the front transaxle case.

      SST
      09308-00010