MANUAL TRANSAXLE UNIT > DISASSEMBLY |
| 1. REMOVE MANUAL TRANSMISSION FILLER PLUG |
![]() |
Remove the filler plug and gasket from the manual transmission case.
| 2. REMOVE MANUAL TRANSMISSION DRAIN PLUG |
![]() |
Remove the drain plug and gasket from the front transaxle case.
| 3. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY |
![]() |
Using a 27 mm deep socket wrench, remove the back-up light switch and gasket from the manual transmission case.
| 4. REMOVE TRANSMISSION CASE PLUG |
![]() |
Remove the transmission case plug and gasket from the manual transmission case.
| 5. REMOVE CONTROL CABLE BRACKET ASSEMBLY |
![]() |
Remove the 3 bolts and control cable bracket from the manual transmission case.
| 6. REMOVE RELEASE CYLINDER BLEEDER PLUG CAP |
Remove the bleeder plug cap from the release cylinder bleeder plug.
| 7. REMOVE RELEASE CYLINDER BLEEDER PLUG |
Remove the bleeder plug from the clutch release bleeder sub-assembly.
| 8. REMOVE CLUTCH CLUTCH RELEASE CYLINDER TO BLEEDER TUBE |
| 9. REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY |
![]() |
Using a union nut wrench, separate the clutch release bleeder sub-assembly from the clutch release cylinder to bleeder tube.
Remove the 2 bolts and clutch release bleeder sub-assembly from the manual transaxle assembly.
| 10. REMOVE CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY |
![]() |
Remove the clutch tube boot from the manual transaxle assembly.
![]() |
Remove the 3 bolts and clutch release with bearing cylinder assembly and clutch release cylinder to bleeder tube.
![]() |
Using a union nut wrench, remove the clutch release cylinder to bleeder tube from the clutch release with bearing cylinder assembly.
| 11. SECURE MANUAL TRANSAXLE ASSEMBLY |
![]() |
Place the manual transaxle on wooden blocks.
| 12. REMOVE REVERSE IDLER GEAR SHAFT BOLT |
![]() |
Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.
| 13. REMOVE LOCK BALL PIN |
![]() |
Using a 10 mm hexagon socket wrench, remove the plug from the manual transmission case.
Using a magnet hand, remove the compression spring and lock ball pin from the manual transmission case.
![]() |
Using a 10 mm hexagon socket wrench, remove the plug from the manual transmission case.
Using a magnet hand, remove the compression spring and lock ball pin from the manual transmission case.
| 14. REMOVE SHIFT DETENT BALL |
![]() |
Using a 6 mm hexagon socket wrench, remove the shift detent ball plug from the manual transmission case.
Using a magnet hand, remove the compression spring and shift detent ball from the manual transmission case.
![]() |
Using a 6 mm hexagon socket wrench, remove the 2 shift detent ball plugs from the manual transmission case.
Using a magnet hand, remove the 2 compression springs and 2 shift detent balls from the manual transmission case.
| 15. REMOVE OUTER SHIFT LEVER E-RING |
![]() |
Remove the E-ring from the outer No. 1 shift lever.
| 16. REMOVE MANUAL TRANSMISSION CASE |
![]() |
Remove the 17 bolts.
![]() |
Using a screwdriver with its tip wrapped with protective tape, separate the manual transmission case from the front transaxle case.
| *1 | Protective Tape |
![]() |
Turn the outer No. 1 shift lever clockwise until it comes into contact with the boss.
![]() |
Push the outer No. 1 shift lever and remove the manual transmission case.
| 17. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY |
![]() |
Remove the reverse idler gear, thrust washer and reverse idler gear shaft from the front transaxle case.
| 18. REMOVE REVERSE SHIFT FORK SHAFT ASSEMBLY |
![]() |
Turn the reverse shift fork shaft clockwise and remove it from the front transaxle case.
| 19. REMOVE REVERSE SHIFT FORK |
![]() |
Using a 5 mm pin punch and hammer, tap out the reverse shift fork slotted spring pin.
Remove the reverse shift fork from the reverse shift fork shaft.
| 20. REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY |
![]() |
Using a 6 mm hexagon socket wrench, remove the 2 bolts and reverse shift arm bracket from the front transaxle case.
| 21. REMOVE OUTER SELECT LEVER |
![]() |
Remove the inner select lever bolt.
![]() |
Remove the outer select lever and inner select lever from the front transaxle case.
| 22. REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY |
![]() |
Turn the shift and select lever shaft clockwise and remove it from the front transaxle case.
| 23. REMOVE OUTER SELECT LEVER OIL SEAL |
![]() |
Using a screwdriver with its tip wrapped with protective tape, remove the outer select lever oil seal from the front transaxle case.
| *1 | Protective Tape |
| 24. REMOVE INPUT SHAFT ASSEMBLY |
![]() |
Remove the input shaft assembly, output shaft assembly and 2 gear shift fork shaft assemblies from the front transaxle case.
Remove the output shaft assembly together with the No. 1 gear shift fork shaft assembly from the input shaft assembly.
Remove the No. 1 gear shift fork shaft assembly from the output shaft assembly.
Remove the No. 2 gear shift fork shaft assemblies from the input shaft assembly.
| 25. REMOVE DIFFERENTIAL CASE ASSEMBLY |
![]() |
Remove the differential case from the front transaxle case.
| 26. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
![]() |
Using SST, remove the front differential case front tapered roller bearing (outer race) and front differential oil baffle from the front transaxle case.
![]() |
Using SST, remove the differential case assembly front tapered roller bearing from the differential case assembly.
| *1 | Turn |
| *2 | Hold |
| 27. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
![]() |
Using SST, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear shim from the manual transmission case.
![]() |
Using SST, remove the front differential case rear tapered roller bearing from the front differential case assembly.
| *1 | Turn |
| *2 | Hold |
| 28. REMOVE TRANSMISSION MAGNET |
![]() |
Remove the transmission magnet from the front transaxle case.
| 29. REMOVE BREATHER PLUG |
![]() |
Remove the breather plug from the front transaxle case.
| 30. REMOVE FRONT OUTPUT SHAFT BEARING |
![]() |
Using SST, tap the front output shaft bearing (outer race) from the front transaxle case.
![]() |
Remove the output shaft cover from the front transaxle case.
| 31. REMOVE TRANSMISSION CASE OIL SEAL (for RH SIDE) |
![]() |
Using SST, remove the transmission case oil seal from the front transaxle case.
| 32. REMOVE FRONT TRANSAXLE CASE OIL SEAL |
![]() |
Using SST, tap out the front transaxle case oil seal from the front transaxle case.
| 33. REMOVE STRAIGHT PIN |
![]() |
Remove the 5 straight pins from the front transaxle case.
| 34. REMOVE REAR INPUT SHAFT BEARING SHIM |
![]() |
Remove the rear input shaft bearing shim from the manual transmission case.
| 35. REMOVE INPUT SHAFT COVER |
![]() |
Remove the input shaft cover from the manual transmission case.
| 36. REMOVE NO. 1 OIL RECEIVER PIPE |
![]() |
Remove the No. 1 oil receiver pipe from the manual transmission case.
| 37. REMOVE OUTER NO. 1 SHIFT LEVER |
![]() |
Using a 5 mm pin punch and hammer, tap out the inner shift lever slotted spring pin.
Remove the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever from the manual transmission case.
| 38. REMOVE OUTER SHIFT LEVER OIL SEAL |
![]() |
Using a screwdriver with its tip wrapped with protective tape, remove the outer shift lever oil seal from the front transaxle case.
| 39. REMOVE REAR OUTPUT SHAFT BEARING |
![]() |
Using SST, remove the rear output shaft bearing (outer race) and rear output shaft bearing shim from the manual transmission case.
| 40. REMOVE TRANSMISSION CASE OIL SEAL (for LH SIDE) |
![]() |
Using SST, remove the transmission case oil seal from the manual transmission case.