VALVE CLEARANCE > ADJUSTMENT |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT WHEEL RH |
| 3. REMOVE NO. 1 ENGINE UNDER COVER |
| 4. REMOVE FRONT FENDER APRON RH |
| 5. REMOVE NO. 1 ENGINE COVER |
![]() |
Remove the 2 nuts and cover.
| 6. REMOVE IGNITION COIL ASSEMBLY |
Disconnect the 4 ignition coil connectors.
![]() |
Remove the 4 bolts and 4 ignition coils.
| 7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Disconnect the 2 ventilation hoses from the cylinder head cover.
![]() |
Remove the 2 bolts and disconnect the 2 engine wires.
![]() |
Remove the 8 bolts, 2 nuts and cylinder head cover.
| 8. SET NO. 1 CYLINDER TO TDC/COMPRESSION |
![]() |
Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.
Check that each timing mark of the camshaft timing gear and sprocket is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
If not, turn the crankshaft by 1 revolution (360°) to align the timing marks as above.
| 9. CHECK VALVE CLEARANCE |
![]() |
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
| Item | Standard Condition |
| Intake | 0.21 to 0.27 mm (0.0083 to 0.0106 in.) |
| Exhaust | 0.38 to 0.48 mm (0.0150 to 0.0189 in.) |
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve clearance lifters.
Turn the crankshaft 1 revolution (360°) and set the No. 4 cylinder to the TDC/compression.
![]() |
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
| Item | Standard Condition |
| Intake | 0.21 to 0.27 mm (0.0083 to 0.0106 in.) |
| Exhaust | 0.38 to 0.48 mm (0.0150 to 0.0189 in.) |
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.
| 10. ADJUST VALVE CLEARANCE |
Remove the No. 2 camshaft .
Remove the camshaft .
Remove the valve lifters.
![]() |
Using a micrometer, measure the thickness of the removed valve lifters.
Calculate the thickness of a new lifter so that the valve clearance comes within the specified values.
| Item | Specification |
| Intake | A = B + (C - 0.24 mm (0.0095 in.)) |
| Exhaust | A = B + (C - 0.35 mm (0.0138 in.)) |
| A | New lifter thickness |
| B | Used lifter thickness |
| C | Measured valve clearance |
Select a new lifter with a thickness as close as possible to the calculated values.
![]() |
Valve lifter selection chart (intake).

| Lifter No. | Thickness mm (in.) | Lifter No. | Thickness mm (in.) | Lifter No. | Thickness mm (in.) |
| 06 | 5.060 (0.1992) | 30 | 5.300 (0.2087) | 54 | 5.540 (0.2181) |
| 08 | 5.080 (0.2000) | 32 | 5.320 (0.2094) | 56 | 5.560 (0.2189) |
| 10 | 5.100 (0.2008) | 34 | 5.340 (0.2102) | 58 | 5.580 (0.2197) |
| 12 | 5.120 (0.2016) | 36 | 5.360 (0.2110) | 60 | 5.600 (0.2205) |
| 14 | 5.140 (0.2024) | 38 | 5.380 (0.2118) | 62 | 5.620 (0.2213) |
| 16 | 5.160 (0.2031) | 40 | 5.400 (0.2126) | 64 | 5.640 (0.2220) |
| 18 | 5.180 (0.2039) | 42 | 5.420 (0.2134) | 66 | 5.660 (0.2228) |
| 20 | 5.200 (0.2047) | 44 | 5.440 (0.2142) | 68 | 5.680 (0.2236) |
| 22 | 5.220 (0.2055) | 46 | 5.460 (0.2150) | 70 | 5.700 (0.2244) |
| 24 | 5.240 (0.2063) | 48 | 5.480 (0.2157) | 72 | 5.720 (0.2252) |
| 26 | 5.260 (0.2071) | 50 | 5.500 (0.2165) | 74 | 5.740 (0.2260) |
| 28 | 5.280 (0.2079) | 52 | 5.520 (0.2173) | - | - |
Valve lifter selection chart (exhaust).

| Lifter No. | Thickness mm (in.) | Lifter No. | Thickness mm (in.) | Lifter No. | Thickness mm (in.) |
| 06 | 5.060 (0.1992) | 30 | 5.300 (0.2087) | 54 | 5.540 (0.2181) |
| 08 | 5.080 (0.2000) | 32 | 5.320 (0.2094) | 56 | 5.560 (0.2189) |
| 10 | 5.100 (0.2008) | 34 | 5.340 (0.2102) | 58 | 5.580 (0.2197) |
| 12 | 5.120 (0.2016) | 36 | 5.360 (0.2110) | 60 | 5.600 (0.2205) |
| 14 | 5.140 (0.2024) | 38 | 5.380 (0.2118) | 62 | 5.620 (0.2213) |
| 16 | 5.160 (0.2031) | 40 | 5.400 (0.2126) | 64 | 5.640 (0.2220) |
| 18 | 5.180 (0.2039) | 42 | 5.420 (0.2134) | 66 | 5.660 (0.2228) |
| 20 | 5.200 (0.2047) | 44 | 5.440 (0.2142) | 68 | 5.680 (0.2236) |
| 22 | 5.220 (0.2055) | 46 | 5.460 (0.2150) | 70 | 5.700 (0.2244) |
| 24 | 5.240 (0.2063) | 48 | 5.480 (0.2157) | 72 | 5.720 (0.2252) |
| 26 | 5.260 (0.2071) | 50 | 5.500 (0.2165) | 74 | 5.740 (0.2260) |
| 28 | 5.280 (0.2079) | 52 | 5.520 (0.2173) | - | - |
Install the selected valve lifter.
| 11. INSTALL CAMSHAFT |
Apply a light coat of engine oil to the journal portion of the camshaft.
![]() |
Install the timing chain onto the camshaft timing gear with the paint mark aligned with the timing mark in the camshaft timing gear as shown in the illustration.
![]() |
Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.
Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.
![]() |
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
| 12. INSTALL NO. 2 CAMSHAFT |
Apply a light coat of engine oil to the journal portion of the No. 2 camshaft.
![]() |
Put the No. 2 camshaft on the cylinder head with the paint mark of the chain aligned with the timing mark on the camshaft timing sprocket.
![]() |
While holding the No. 2 camshaft by hand, temporarily tighten the camshaft timing sprocket set bolt.
![]() |
Examine the front marks, and numbers and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
![]() |
While holding the camshaft with a wrench, tighten the camshaft timing sprocket set bolt.
![]() |
Check that the paint marks on the chain are aligned with the timing marks on the camshaft timing gear and camshaft timing sprocket. Also, check that the crankshaft pulley groove is aligned with the timing mark "0" of the timing chain cover.
| 13. INSTALL NO. 1 CHAIN TENSIONER |
![]() |
Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.
![]() |
Install a new gasket and the chain tensioner with the 2 nuts.
![]() |
Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.
![]() |
Turn the crankshaft clockwise, then check that the plunger is extended.
| 14. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Remove any old packing material from the contact surface.
![]() |
Apply seal packing to the 2 locations shown in the illustration.
![]() |
Install the cylinder head cover with the 8 bolts and 2 nuts.
![]() |
Install the 2 engine wires with the 2 bolts.
Connect the clamp of the engine wire (labeled B).
![]() |
Connect the 2 ventilation hoses to the cylinder head cover.
| 15. INSTALL IGNITION COIL ASSEMBLY |
![]() |
Install the 4 ignition coils with the 4 bolts.
Connect the 4 ignition coil connectors.
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 17. CHECK FOR ENGINE OIL LEAKS |
| 18. INSTALL NO. 1 ENGINE COVER |
![]() |
Install the engine cover with the 2 nuts.
| 19. INSTALL FRONT FENDER APRON RH |
| 20. INSTALL NO. 1 ENGINE UNDER COVER |
| 21. INSTALL FRONT WHEEL RH |