CYLINDER HEAD > INSPECTION |
| 1. INSPECT CYLINDER HEAD FOR WARPAGE |
![]() |
Using a precision straightedge and a feeler gauge, measure the surface that is in contact with the cylinder block and the manifolds for warpage.
| 2. INSPECT CYLINDER HEAD FOR CRACKS |
![]() |
Using a dye penetrant, inspect the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks.
If cracked, replace the cylinder head.
| 3. INSPECT VALVE SEAT |
Apply a light coat of Prussian blue (or white lead) to the valve face.
Lightly press the valve against the seat.
![]() |
Check the valve face and seat in accordance with the following procedure.
If blue appears 360°around the face, the valve is concentric. If not, replace the valve.
If blue appears 360°around the valve seat, the guide and face are concentric. If not, resurface the valve seat .
Check that the seat contact is in the middle of the valve face with a width.
| Item | Standard Condition |
| Intake | 1.0 to 1.4 mm (0.0039 to 0.0551 in.) |
| Exhaust | 1.2 to 1.6 mm (0.0472 to 0.0630 in.) |
| 4. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Check the lock of the camshaft timing gear.
Clamp the camshaft in a vise, and confirm that the camshaft timing gear is locked.
Release the lock pin.
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Break through the tape of the advance side path and the retard side path on the opposite side of the groove.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the paths whose tape was broken in the procedure above.
Check that the camshaft timing gear revolves in the advance direction when weakening the air pressure of the retard side path.
When the camshaft timing gear reaches the extreme advance position, remove the air gun from the retard side path and advance side path, in that order.
Check for smooth rotation.
Rotate the camshaft timing gear within its movable range several times, but do not turn it to the extreme retard position. Check that the gear rotates smoothly.
Check the lock in the extreme retard position.
Confirm that the camshaft timing gear is locked at the extreme retard position.
| 5. INSPECT CAMSHAFT |
![]() |
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
![]() |
Inspect the camshaft journals.
Using a micrometer, measure the journal diameter.
| Journal Position | Specified Condition |
| No. 1 | 35.971 to 35.985 mm (1.4162 to 1.4167 in.) |
| Other | 22.959 to 22.975 mm (0.9039 to 0.9045 in.) |
| 6. INSPECT NO. 2 CAMSHAFT |
![]() |
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
![]() |
Inspect the camshaft journals.
Using a micrometer, measure the journal diameter.
| Journal Position | Specified Condition |
| No. 1 | 35.971 to 35.985 mm (1.4162 to 1.4167 in.) |
| Other | 22.959 to 22.975 mm (0.9039 to 0.9045 in.) |
| 7. INSPECT CAMSHAFT OIL CLEARANCE |
![]() |
Clean the 10 bearing caps and camshaft journals.
Place the 2 camshafts on the cylinder head.
Lay a strip of Plastigage across each of the camshaft journals.
Install the 10 bearing caps .
Remove the 10 bearing caps for No. 2 camshaft and for camshaft .
![]() |
Measure the Plastigage at its widest point.
| Item | Standard Condition |
| Intake No. 1 journal | 0.007 to 0.038 mm (0.0003 to 0.0015 in.) |
| Exhaust No. 1 journal | 0.040 to 0.079 mm (0.0016 to 0.0031 in.) |
| Other journal | 0.025 to 0.062 mm (0.0010 to 0.0024 in.) |
| Item | Standard Condition |
| Intake No. 1 journal | 0.07 mm (0.0028 in.) |
| Other journal | 0.10 mm (0.0039 in.) |
| Mark | Standard Condition |
| Mark 1 | 40.000 to 40.008 mm (1.5748 to 1.5751 in.) |
| Mark 2 | 40.009 to 40.017 mm (1.5752 to 1.5755 in.) |
| Mark 3 | 40.018 to 40.025 mm (1.5755 to 1.5758 in.) |
| Mark | Standard Condition |
| Mark 1 | 2.000 to 2.004 mm (0.0787 to 0.0789 in.) |
| Mark 2 | 2.005 to 2.008 mm (0.0789 to 0.0791 in.) |
| Mark 3 | 2.009 to 2.012 mm (0.0791 to 0.0792 in.) |
| 8. INSPECT CAMSHAFT THRUST CLEARANCE |
![]() |
Install the 2 camshafts .
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| Item | Standard Condition |
| Intake | 0.040 to 0.095 mm (0.0016 to 0.0037 in.) |
| Exhaust | 0.080 to 0.135 mm (0.0032 to 0.0053 in.) |
| Item | Standard Condition |
| Intake | 0.11 mm (0.0043 in.) |
| Exhaust | 0.15 mm (0.0059 in.) |
| 9. INSPECT VALVE LIFTER |
![]() |
Using a micrometer, measure the lifter diameter.
| 10. INSPECT VALVE LIFTER OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the valve lifter bore diameter of the cylinder head.
Subtract the valve lifter diameter measurement from the valve lifter bore diameter measurement.
| 11. INSPECT INNER COMPRESSION SPRING |
![]() |
Using vernier calipers, measure the free length of the valve spring.
![]() |
Using a steel square, measure the deviation of the inner compression spring.
| 12. INSPECT INTAKE VALVE |
![]() |
Using a gasket scraper, chip off any carbon on the valve head.
Using a wire brush, thoroughly clean the valve.
![]() |
Using a vernier caliper, measure the valve overall length.
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
| 13. INSPECT EXHAUST VALVE |
![]() |
Using a gasket scraper, chip off any carbon on the valve head.
Using a wire brush, thoroughly clean the valve.
![]() |
Using vernier calipers, measure the valve overall length.
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using vernier calipers, measure the valve head margin thickness.
| 14. INSPECT INTAKE VALVE GUIDE BUSH |
![]() |
Using a caliper gauge, measure the inside diameter of the guide bush.
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
| 15. INSPECT EXHAUST VALVE GUIDE BUSH |
![]() |
Using a caliper gauge, measure the inside diameter of the guide bush.
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
| 16. INSPECT CYLINDER HEAD SET BOLT |
![]() |
Using a vernier caliper, measure the length of the head bolts from the seat to the end.
| 17. INSPECT EXHAUST MANIFOLD |
![]() |
Using a precision straightedge and a feeler gauge, measure the surface contacting the cylinder head for warpage.