Home › ENGINE ยท 2AZ-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REPLACEMENT

for Preparation Click here



1. REPLACE TIMING CHAIN COVER OIL SEAL

HINT:
There are 2 methods to replace the oil seal.



  1. If the timing chain cover is removed from the cylinder block:



      A112248
    1. Using a screwdriver and hammer, tap out the oil seal.

    2. Apply multi-purpose grease to the lip of a new oil seal.

      NOTICE:
      Keep the lip free of foreign objects.



    3. A112249E02
    4. Using SST and a hammer, tap in the new oil seal until its surface is flush with the timing chain cover edge.

      SST
      09223-22010  

      NOTICE:
      Do not tap the oil seal at an angle.



  1. If the timing chain cover oil seal is installed to the cylinder block:

    1. Remove fan and generator V belt (Click here).

    2. Remove the crankshaft pulley .



    3. A077418E02
    4. Using a knife, cut off the lip of the oil seal.

    5. Using a screwdriver with its tip wrapped with tape, pry out the oil seal.

      NOTICE:
      After removing, check the crankshaft for damage. If damaged, smooth the surface with 400-grit sandpaper.

    6. Apply multi-purpose grease to the lip of a new oil seal.

      NOTICE:
      Keep the lip free of foreign objects.



    7. A077419E02
    8. Using SST and a hammer, tap in the new oil seal until its surface is flush with the timing chain cover edge.

      SST
      09223-22010  

      NOTICE:
      Do not tap the oil seal at an angle.

    9. Install the crankshaft pulley .

    10. Install the fan and generator V belt (Click here).



2. REPLACE ENGINE REAR OIL SEAL


    A098356E01
  1. Using a knife, cut off the lip of the oil seal.

  1. Using a screwdriver with its tip wrapped with tape, pry out the oil seal.

    NOTICE:
    After removing, check the crankshaft for damage. If damaged, smooth the surface with 400-grit sandpaper.

  1. Apply multi-purpose grease to the lip of a new oil seal.

    NOTICE:
    Keep the lip free of foreign objects.



    A077422E01
  1. Using SST and a hammer, tap in the new oil seal until its surface is flush with the rear oil seal retainer edge.

    SST
    09223-15030  
    09950-70010   (09951-07100)

    NOTICE:
    1. Wipe any extra grease off the crankshaft.
    2. Do not tap the oil seal at an angle.



3. REPLACE STUD BOLT (for Cylinder Block)

NOTICE:
If the stud bolt is deformed or the threads ate damaged, replace it.

  1. Remove the 8 stud bolts.



  1. Install the 8 stud bolts into the cylinder block.

    Torque:
    Item
    Specified Condition
    A
    22 N*m (219 kgf*cm, 16 ft.*lbf)
    B
    5.0 N*m (51 kgf*cm, 44 in.*lbf)
    C
    9.5 N*m (97 kgf*cm, 84 in.*lbf)
    D
    5.0 N*m (51 kgf*cm, 44 in.*lbf)



    A112253E01



4. REPLACE TIGHT PLUG (for Cylinder Block)

NOTICE:
If water leaks from the tight plug or the plug corrodes, replace it.

  1. Remove the 2 tight plugs from the engine front and rear side.



    A058129E01
  1. Apply adhesive around the new tight plugs.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent



  1. Using SST, install the 2 tight plugs.

    SST
    09950-60010   (09951-00200)
    09950-70010   (09951-07100)

    Standard depth:
    Item
    Specified Condition
    A
    1.7 to 2.7 mm (0.067 to 0.106 in.)
    B
    2.2 to 3.2 mm (0.087 to 0.126 in.)



    A098152E01



5. REPLACE RING PIN (for Cylinder Block)

NOTICE:
It is not necessary to remove with ring pin unless it is being replaced.

  1. Remove the 12 ring pins.



  1. Using a plastic hammer, install 12 new ring pins.

    Standard protrusion height:
    Item
    Specified Condition
    A
    6.0 mm (0.236 in.)
    B
    5.0 mm (0.197 in.)



    A112251E01



6. REPLACE STRAIGHT PIN (for Cylinder Block)

NOTICE:
It is not necessary to remove with straight pin unless it is being replaced.

  1. Remove the 8 straight pins.



  1. Using a plastic hammer, install 8 new straight pins.

    Standard protrusion height:
    Item
    Specified Condition
    A
    8.0 mm (0.315 in.)
    B
    7.5 mm (0.295 in.)
    C
    12.0 mm (0.472 in.)
    D
    5.0 mm (0.197 in.)



    A112252E01