CLUTCH MASTER CYLINDER (for LHD) > INSTALLATION |
| 1. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY |
Install the clutch master cylinder with the 2 nuts.
| 2. CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE |
![]() |
Using a union nut wrench, connect the flexible hose tube.
| 3. CONNECT CLUTCH RESERVOIR TUBE |
![]() |
Connect the clutch reservoir tube to the clutch master cylinder with the clip.
| 4. CONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS |
![]() |
Apply MP grease to the contact surface of the pin and clevis bush.
Connect the clevis to the clutch pedal with the pin and clip.
Install the clip to the pin.
| 5. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Knee Airbag) |
![]() |
Connect the connector.
Install the driver side knee airbag with the 4 bolts.
| 6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag) |
![]() |
Attach the 8 claws to install the lower instrument panel finish panel.
Install the 2 screws.
| 7. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Attach the 3 claws to install the cover.
Install the 2 screws.
| 8. INSTALL COWL BODY MOUNTING REINFORCEMENT LH |
![]() |
Install the mounting reinforcement with the 2 nuts.
| 9. INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY |
![]() |
Install the cowl top panel outer with the 14 bolts.
| 10. INSTALL COWL VENTILATOR HOUSING SUB-ASSEMBLY |
![]() |
Attach the 4 claws to install ventilator housing.
| 11. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Connect the connector and attach the clamp.
Move the wiper motor and link in the direction shown by the arrow in the illustration to attach the wiper cushion to the body, and install the wiper motor and link.
Install the 2 bolts.
| 12. INSTALL COWL TOP VENTILATOR LOUVER |
![]() |
Attach the 12 claws and install the louver.
Install the 2 clips.
| 13. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Attach the claw to install the front fender to cowl side seal.
| 14. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
![]() |
Attach the claw to install the front fender to cowl side seal.
| 15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Clean the wiper arm serration with a round file or equivalent.
Clean the wiper pivot serration with a wire brush.
![]() |
Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.
Operate the front wipers while spraying water or washer fluid on the windshield. Ensure that there is no interference between the blades and pillar.
| 16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Stop the wiper motor at the automatic stop position.
Clean the wiper arm serration with a round file or equivalent.
Clean the wiper pivot serration with a wire brush.
![]() |
Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.
| 17. INSTALL FRONT WIPER ARM HEAD CAP |
Install the 2 caps.
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 19. CHECK SRS WARNING LIGHT |
Check the SRS warning light (Click here).
| 20. BLEED CLUTCH PIPE LINE |
Fill the brake reservoir with brake fluid and bleed the clutch system.
| 21. CHECK BRAKE FLUID |
Check the brake fluid (Click here).
| 22. CHECK FLUID LEVEL IN RESERVOIR |
![]() |
Check the fluid level and add fluid if necessary.
| 23. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY |
Lift up the floor carpet to expose the asphalt sheet under the pedal.
![]() |
Check that the pedal height is correct.
Adjust the pedal height.
Loosen the lock nut and turn the stopper bolt or clutch switch assembly until the pedal height is within the specified range.
Tighten the lock nut.
![]() |
Check the pedal free play and push rod play.
Depress the clutch pedal until resistance is felt.
Measure the distance between the pedal's released position and the position in the previous step.
Release the pedal. Using your finger, gently press the pedal until resistance increases slightly.
Measure the distance between the pedal's released position and the position in the previous step.
Adjust the pedal free play and push rod play.
Loosen the lock nut and turn the push rod until the pedal free play and push rod play are within the specified ranges.
Tighten the lock nut.
Check the pedal height.
![]() |
Check the clutch release point.
Apply the parking brake and use wheel chocks.
Start the engine and run it at idle.
Without depressing the clutch pedal, slowly move the shift lever to R until the gears contact.
Gently depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) to the full stroke end position.