Home › ENGINE · 2GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to the IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the integration relay (EFI MAIN relay) and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM


A136793E04


INSPECTION PROCEDURE

1.INSPECT FUSES (P/I, AM2, IG2, EFI MAIN AND IGN)


    A138575E01
  1. Remove the P/I fuse, AM2 fuse, IG2 fuse and EFI MAIN fuse from the engine room No. 1 relay block.

  1. Remove the IGN fuse from the instrument panel junction block.

  1. Measure the resistance of the fuses.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the fuses.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2.INSPECT RELAY (IG2, EFI MAIN)


    A138576E02
  1. Remove the integration relay and IG2 relay from the engine room No. 1 relay block.

  1. Measure the resistance between the terminals of the integration relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    1C-1 - 1A-4
    10 kΩ or higher
    Below 1 Ω
    (When battery voltage is applied to terminals 1A-2 and 1A-3)

  1. Measure the resistance between the terminals of the IG2 relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    Below 1 Ω
    (When battery voltage is applied to terminals 1 and 2)

  1. Reinstall the IG2 relay.



NG
REPLACE RELAY
OK


3.CHECK WIRE HARNESS (ECM - BODY GROUND)


    A136305E36
  1. Disconnect the ECM connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    B96-81 (E1) - Body ground
    Below 1 Ω

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT ECM (IGSW VOLTAGE)


    A107934E64
  1. Disconnect the ECM connectors.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage between the terminals of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    A12-28 (IGSW) - B96-81 (E1)
    9 to 14 V

  1. Reconnect the ECM connector.



OK
REPLACE ECM (Click here)
NG


5.CHECK WIRE HARNESS (RELAY BLOCK, ECM, IGNITION SWITCH, BATTERY)


    A138577E03
  1. Disconnect the ECM connector.

  1. Disconnect the ignition switch connector.

  1. Disconnect the cable from the battery positive terminal.

  1. Remove the AM2 fuse and IG2 relay.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    A12-28 (IGSW) - IG2 relay terminal 5
    Below 1 Ω
    IG2 relay terminal 2 - Body ground
    Below 1 Ω
    Positive (+) battery cable - IG2 relay terminal 3
    Below 1 Ω
    Positive (+) battery cable - AM2 fuse terminal 1
    Below 1 Ω
    E5-7 (AM2) - AM2 fuse terminal 2
    Below 1 Ω
    E5-6 (IG2) - IG2 relay terminal 1
    Below 1 Ω
    A12-28 (IGSW) or IG2 relay terminal 5 - Body ground
    10 kΩ or higher
    Positive (+) battery cable or AM2 fuse terminal 1 - Body ground
    10 kΩ or higher
    Positive (+) battery cable or IG2 relay terminal 3 - Body ground
    10 kΩ or higher
    E5-7 (AM2) or AM2 fuse terminal 2 - Body ground
    10 kΩ or higher
    E5-6 (IG2) or IG2 relay terminal 1 - Body ground
    10 kΩ or higher

  1. Reinstall the relay and fuse.

  1. Reconnect the connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT IGNITION SWITCH
Click here


NG
REPLACE IGNITION SWITCH (Click here)
OK


7.CHECK WIRE HARNESS (INTEGRATION RELAY - ECM, BATTERY AND BODY GROUND)


    A138578E03
  1. Disconnect the ECM connector.

  1. Disconnect the cable from the battery positive terminal.

  1. Remove the integration relay from the engine room No. 1 relay block.

  1. Disconnect the integration relay connector.

  1. Remove the P/I fuse from the engine room No. 1 relay block.

  1. Measure the resistance between the terminals.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    A12-2 (+B) - 1A-4
    Below 1 Ω
    A12-1 (+B2) - 1A-4
    Below 1 Ω
    A12-44 (MREL) - 1A-2
    Below 1 Ω
    P/I fuse terminal 2 - 1C-1
    Below 1 Ω
    P/I fuse terminal 1 - Positive (+) battery cable
    Below 1 Ω
    1A-3 - Body ground
    Below 1 Ω
    A12-2 (+B) or 1A-4 - Body ground
    10 kΩ or higher
    A12-1 (+B2) or 1A-4 - Body ground
    10 kΩ or higher
    A12-44 (MREL) or 1A-2 - Body ground
    10 kΩ or higher
    P/I fuse terminal 2 or 1C-1 - Body ground
    10 kΩ or higher
    P/I fuse terminal 1 or Positive (+) battery cable - Body ground
    10 kΩ or higher

  1. Reconnect the connectors.

  1. Reconnect the cable to the battery positive terminal.

  1. Reinstall the integration relay and P/I fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE ENGINE ROOM NO. 1 RELAY BLOCK