Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › REAR AIRBAG SENSOR

REAR AIRBAG SENSOR > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.

CAUTION:
Be sure to read the precautionary notices concerning the SRS airbag system before servicing it (Click here).



1. INSTALL AIRBAG SENSOR REAR LH


    B127923E01
  1. Install the airbag sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.



2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Short Body)


B129712
  1. Install the belt hanger to the trim board.

  1. Connect the power outlet socket connector.

  1. Attach the 5 clips and 5 claws to install the trim board.

  1. Install the bolt and 2 screws.



    B137546
  1. Connect the rear No.1 seat belt's floor anchor.

    1. Connect the floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Install the anchor cover.



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Long Body)


    B129706
  1. Install the belt hanger to the trim board.

  1. Connect the power outlet socket connector.

  1. Attach the 4 clips and 5 claws to install the trim board.

  1. Install the 2 screws and 2 bolts.



    B137546
  1. Connect the rear No.1 seat belt's floor anchor.

    1. Connect the floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Install the anchor cover.



4. CONNECT REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH


B133643
  1. Connect the seat belt's floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Attach the lap belt outer anchor cover.



5. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET


6. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER


7. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH


8. INSTALL REAR FLOOR FINISH PLATE (for Short Body)


    B129716
  1. Attach the 6 clips to install the finish plate.



9. INSTALL REAR FLOOR FINISH PLATE (for Long Body)


    B129704
  1. Attach the 2 claws and 6 clips to install the finish plate.



10. INSTALL BACK DOOR WEATHERSTRIP


11. INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE


B129717
  1. Attach the 7 clips to install the side plate.

  1. Install the 4 screws.



12. INSTALL JACK CARRIER ASSEMBLY (for Short Body)


    B129715
  1. Install the jack carrier with the 7 clips.



13. INSTALL REAR FLOOR NO. 3 BOARD


14. INSTALL REAR FLOOR NO. 2 BOARD


15. INSTALL DECK BOARD ASSEMBLY


16. INSTALL REAR FLOOR NO. 1 BOARD


17. INSTALL TONNEAU COVER ASSEMBLY


18. INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY


19. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


20. INSTALL REAR DOOR SCUFF PLATE LH (for Short Body)


    B129711
  1. Attach the 8 claws to install the scuff plate.



21. INSTALL REAR DOOR SCUFF PLATE LH (for Long Body)


    B129703
  1. Attach the 9 claws and 2 clips to install the scuff plate.



22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


23. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).