AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) > TERMINALS OF ECU |
| CHECK AIR CONDITIONING AMPLIFIER |

Measure the voltage of the connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| LOCK (E42-3) - SG-2 (E42-10) (*2) | W - G | Compressor lock sensor signal | Ignition switch on (IG) AUTO switch ON A/C switch ON Magnetic clutch ON | Pulse generation (see waveform 4) |
| S5-3 (E42-7) - GND (E42-24) | B - W-B | Power supply for pressure sensor | Ignition switch on (IG) | 4.5 to 5.5 V |
| CANH (E42-8) - GND (E42-24) | V - W-B | Hi-level CAN bus line | Ignition switch on (IG) | Pulse generation (see waveform 1) |
| CANL (E42-9) - GND (E42-24) | W - W-B | Lo-level CAN bus line | Ignition switch on (IG) | Pulse generation (see waveform 2) |
| SG-2 (E42-10) - Body ground | G - Body ground | Ground for pressure sensor | Always | Below 1 V |
| PRE (E42-12) - SG-2 (E42-10) | L - G | Air conditioning pressure sensor signal | Refrigerant pressure: normal | 0.76 to 4.74 V |
| PRE (E42-12) - SG-2 (E42-10) | L - G | Air conditioning pressure sensor signal | Refrigerant pressure: Abnormal (less than 0.196 MPa [2.0 kgf/cm2, 28 psi] | Below 0.76 V |
| PRE (E42-12) - SG-2 (E42-10) | L - G | Air conditioning pressure sensor signal | Refrigerant pressure: Abnormal (more than 3.14 MPa [32 kgf/cm2, 455 psi]) | 4.74 V or more |
| SOL+ (E42-13) - GND (E42-24) | GR - W-B | A/C compressor operation signal | Engine idling | Pulse generation (see waveform 3) |
| Heater control (blower switch): 1 | ||||
| A/C switch ON | ||||
| IG+ (E42-14) - GND (E42-24) | Y - W-B | Power source (IG) | Ignition switch on (IG) | 10 to 14 V |
| MGC (E42-15) - GND (E42-24) (*2) | V - W-B | Magnetic clutch relay signal | Ignition switch on (IG) Magnetic clutch OFF | 10 to14 V |
| MGC (E42-15) - GND (E42-24) (*2) | V - W-B | Magnetic clutch relay signal | Ignition switch on (IG) Magnetic clutch ON | Below 1.5 V |
| SBLW (E42-21) - GND (E42-24) | GR - W-B | Blower motor ON signal | Ignition switch on (IG) | 10 to 14 V → Below 1 V |
| Heater control (blower switch): 0 → 1 | ||||
| TE (E42-22) - SG-3 (E42-23) | W - B | Evaporator temperature sensor signal | Ignition switch on (IG) | 1 to 1.3 V |
| Temperature near evaporator: 15°C (59°F) | ||||
| SG-3 (E42-23) - Body ground | B - Body ground | Ground for evaporator temperature sensor | Always | Below 1 V |
| GND (E42-24) - Body ground | W-B - Body ground | Ground for main power supply | Always | Below 1 V |
| A/C (E42-27) - GND (E42-24) | P - W-B | A/C switch signal | Ignition switch on (IG) | Below 1 V → 10 to 14 V |
| A/C switch OFF → ON | ||||
| LED (E42-28) - Body ground | GR - Body ground | A/C switch indicator signal | Engine idling | 10 to 14 V → Below 4 V |
| A/C switch ON | ||||
| Heater control (blower switch): 0 → 1 | ||||
| B (E43-1) - GND (E42-24) (*1) | R - W-B | Power source (Back-up) | Always | 10 to 14 V |
| PTC1 (E43-9) - GND (E42-24) (*1) | W - W-B | PTC NO. 1 heater relay operation signal | Engine idling | Below 1 V → 10 to 14 V |
| Air mix control knob: Max hot | ||||
| Engine coolant temperature: Below 65°C (149°F) | ||||
| Ambient temperature: Below 10°C (50°F) | ||||
| Light control switch: OFF | ||||
| Heater control (blower switch): 0 → 1 | ||||
| Waiting time: 10 seconds | ||||
| PTC2 (E43-10) - GND (E42-24) (*1) | B - W-B | PTC NO. 2 heater relay operation signal | Engine idling | Below 1 V → 10 to 14 V |
| Air mix control knob: Max hot | ||||
| Engine coolant temperature: Below 65°C (149°F) | ||||
| Ambient temperature: Below 10°C (50°F) | ||||
| Light control switch: OFF | ||||
| Heater control (blower switch): 0 → 1 | ||||
| Waiting time: 20 seconds | ||||
| HEAT (E43-14) - Body ground (*1) | W - Body ground | MAX HOT switch detection signal | Ignition switch on (IG) | 10 to 14 V |
| Air mix control knob: Max hot | ||||
| Heater control (blower switch): 1 | ||||
| HLS (E43-23) - Body ground (*1) | BR - Body ground | Headlight control signal | Engine idling | Below 1 V |
| Light control switch: head position | ||||
| ALT (E43-24) - GND (E42-24) (*1) | B - W-B | Generator operation signal | Engine idling | Pulse generation |
![]() |
Using an oscilloscope, measure the waveform 1.
| Item | Content |
| Symbols (Terminal No.) | CANH (E42-8) - GND (E42-24) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch on (IG) |
![]() |
Using an oscilloscope, measure the waveform 2.
| Item | Content |
| Symbols (Terminal No.) | CANL (E42-9) - GND (E42-24) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch on (IG) |
![]() |
Using an oscilloscope, measure the waveform 3.
| Item | Content |
| Symbols (Terminal No.) | SOL+ (E42-13) - GND (E42-24) |
| Tool Setting | 5 V/DIV., 500 μsec./DIV. |
| Condition | Engine idling, Blower switch LO, A/C switch ON |
![]() |
Using an oscilloscope, measure the waveform 4.
| Item | Content |
| Symbols (Terminal No.) | LOCK (E42-3) - SG-2 (E42-10) |
| Tool Setting | 500 mV/DIC., 20 msec./DIV. |
| Condition | Ignition switch on (IG), A/C switch ON, Magnetic clutch ON |