Home › BODY › EXTERIOR › OUTSIDE MOULDING

OUTSIDE MOULDING > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. When installing the moulding, heat the vehicle body and moulding using a heat light.

    Standard:
    Item
    Temperature
    Vehicle body
    40 to 60°C (104 to 140°F)
    Moulding
    20 to 30°C (68 to 86°F)

    NOTICE:
    Do not heat the vehicle body and moulding excessively.



1. REPAIR INSTRUCTION
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the rear wheel opening extension.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Installation temperature.

    1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the rear wheel opening extension (installation surface of the front quarter stripe LH) and tape to between 20 to 30°C (68 to 86°F) using a heat light. When the ambient temperature is higher than 35°C (95°F), cool the rear wheel opening extension (installation surface of the front quarter stripe LH) and tape to between 20 to 30°C (68 to 86°F) prior to installation.

      HINT:
      1. The most appropriate temperature for installing the tape is 25°C (77°F).
      2. When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.

  1. Before installation.

    1. Make sure any dirt on and around the rear wheel opening extension where the tape will be installed (installation surface of the front quarter stripe LH) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

      HINT:
      Spray water on the shop floor to settle any dust.

  1. Key points for handling the front quarter stripe LH.

    1. The front quarter stripe LH bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

      NOTICE:
      Do not bend the front quarter stripe LH or leave it in a place with a high temperature.



  1. Key points for the installation of the front quarter stripe LH (how to use a squeegee and the installation procedure for a flat surface).

    NOTICE:
    1. Position the front quarter stripe LH with a high level of accuracy to achieve a neat finish and to avoid peeling.
    2. The front quarter stripe LH cannot be reused because it deforms and will not fit after removal.




    1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf) while moving the squeegee at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.


      B233855E06

      NOTICE:
      Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.

      HINT:
      1. Either angle of the squeegee (for pressing forward or for pulling) is acceptable.
      2. Be sure to apply the front quarter stripe LH while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.



    B233856E03
  1. Key points for the installation of the front quarter stripe LH (how to use a squeegee and the installation procedure for hemming surfaces).

    1. If it is difficult to press the front quarter stripe LH, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the front quarter stripe LH to the hem of the rear wheel opening extension, especially for a small hem.

      HINT:
      When applying front quarter stripe LH to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.

  1. Key points for the installation of the front quarter stripe LH (how to use a squeegee and the installation procedure for corners).

    1. Remove the release paper and apply the front quarter stripe LH carefully with your fingers.

    2. Before applying the front quarter stripe LH to each corner, heat the front quarter stripe LH using a heat light and gradually apply it to avoid wrinkles in the front quarter stripe LH and achieve a neat finish.

  1. Check after installation.

    1. After completing the application, check if the front quarter stripe LH is applied neatly. If the front quarter stripe LH is not applied neatly, apply new front quarter stripe LH.

      NOTICE:
      Do not reuse the tape.



2. INSTALL FRONT QUARTER STRIPE LH

HINT:
When installing the front quarter stripe LH, heat the rear wheel opening extension and front quarter stripe LH using a heat light.

Standard:
Item
Temperature
Front Quarter Stripe LH
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the rear wheel opening extension or front quarter stripe LH excessively.



    B308288E01
  1. Align the cutouts of the application sheet of new front quarter stripe LH with the rear wheel opening extension end lines as shown in the illustration, and then apply the front quarter stripe LH.

  1. Remove the application sheet from the front quarter stripe LH.



3. INSTALL FRONT QUARTER STRIPE LH

HINT:
When installing the front quarter stripe LH, heat the rear wheel opening extension and front quarter stripe LH using a heat light.

Standard:
Item
Temperature
Front Quarter Stripe LH
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the rear wheel opening extension or front quarter stripe LH excessively.



    B308287E01
  1. Align the cutouts of the application sheet of new front quarter stripe LH with the rear wheel opening extension end lines as shown in the illustration, and then apply the front quarter stripe LH.

  1. Remove the application sheet from the front quarter stripe LH.



4. INSTALL NO. 1 ROCKER PANEL MOULDING RETAINER


    B133715
  1. Install the 2 retainers with the 4 screws.



5. INSTALL QUARTER OPENING RETAINER LH


    B133714
  1. Install the retainer with the 4 screws.



6. INSTALL NO. 2 ROCKER PANEL MOULDING RETAINER


    B133713
  1. Install the retainer with the 2 screws.



7. INSTALL REAR QUARTER OUTSIDE MOULDING LH


    B136805
  1. Attach the 5 clips to install the moulding.



    B133709
  1. Using an air riveter or hand riveter with a nose piece, strike 2 rivets to the vehicle to install the rear quarter outside moulding to the vehicle.

    NOTICE:
    1. If the rivet is not positioned perpendicularly, it will bend the mandrel.

    2. B171664E02
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    3. B172390E02
      Confirm that the rivets are seated properly against the moulding.
    4. Do not tilt the riveter when installing the rivet to the moulding.
    5. Do not leave any space between the rivet head and moulding.

    6. B172391E02
      Do not leave any space between the moulding and quarter panel. Firmly hold together the 2 items while installing the rivet.



8. INSTALL NO. 1 REAR WHEEL OPENING EXTENSION LH


    B136804
    B133205
  1. Attach the 5 clips to install the extension.
    Using an air riveter or hand riveter with a nose piece, strike 2 rivets to the vehicle to install the rear wheel opening extension to the vehicle.

    NOTICE:
    1. If the rivet is not positioned perpendicularly, it will bend the mandrel.

    2. B171664E02
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    3. B172390E02
      Confirm that the rivets are seated properly against the moulding.
    4. Do not tilt the riveter when installing the rivet to the moulding.
    5. Do not leave any space between the rivet head and moulding.

    6. B172391E02
      Do not leave any space between the moulding and door panel. Firmly hold together the 2 items while installing the rivet.



9. INSTALL NO. 2 REAR WHEEL OPENING EXTENSION LH
  1. Attach the 2 claws to install the extension.



    B136808
  1. Install the screw.



10. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY LH


    B136809
  1. Attach the 9 clips to install the extension

  1. Install the 4 screws and 2 clip.