SFI SYSTEM > Cranking Holding Function Circuit |


| 1.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG).
Check the result when the engine starts.
| Ignition Switch Condition | Tester Display (Starter Signal) |
| on (IG) | OFF |
| Engine starts | ON |
|
| ||||
| NG | |
| 2.INSPECT ECM (STSW TERMINAL VOLTAGE) |
![]() |
Disconnect the A12 ECM connector.
Depress the clutch pedal fully (for M/T models).
Shift lever is P position (for A/T models).
Measure the voltage between the ECM terminal and the body ground when operating the ignition switch to start cranking.
| Tester Connection | Specified Condition |
| STSW (A12-14) - Body ground | 10 to 14 V |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (STAR OUTPUT VOLTAGE) |
![]() |
Disconnect the A4 clutch start switch connector (for M/T models).
![]() |
Disconnect the B28 Park / Neutral Position (PNP) switch connector (for A/T models)
Measure the voltage between the terminal of clutch start switch or PNP switch connector and the body ground while cranking the engine.
| Tester Connection | Specified Condition |
| B (A4-2) - Body ground | 10 to 14 V |
| Tester Connection | Specified Condition |
| B (B28-4) - Body ground | 10 to 14 V |
Reconnect the clutch start switch connector.
Reconnect the PNP switch connector.
|
| ||||
| OK | |
| 4.INSPECT CLUTCH START SWITCH ASSEMBLY OR PARK / NEUTRAL POSITION SWITCH ASSEMBLY |
M/T:
Disconnect the A4 clutch start switch connector.
![]() |
Measure the resistance between the terminals of the clutch start switch assembly connector.
| Switch Condition | Specified Condition |
| Pushed in | Below 1 Ω |
| Released | 10 kΩ or higher |
A/T:
Disconnect the B28 PNP switch connector.
![]() |
Measure the resistance between each terminal shown below when the shift lever is moved to each range.
| Shift Position | Tester Connection | Specified Condition |
| P | PL (6) - RB (2) | Below 1 Ω |
| L (5) - B (4) | ||
| R | RL (1) - RB (2) | |
| N | NL (9) - RB (2) | |
| L (5) - B (4) | ||
| D | DL (7) - RB (2) | |
| 2 | 2L (3) - RB (2) | |
| L | LL (8) - RB (2) |
|
| ||||
| NG | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU) |
![]() |
Disconnect the E20 main body ECU connector.
Disconnect the A12 ECM connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| STSW (E20-4) - STSW (A12-14) | Below 1 Ω |
| Tester Connection | Specified Condition |
| STSW (E20-4) - Body ground | Below 1 Ω |
Reconnect the main body ECU connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 6.INSPECT ST CUT RELAY |
![]() |
Remove the ST CUT relay from the No. 7 relay block.
Measure the resistance.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (When battery voltage applied to terminals 1 and 2) |
Reinstall the relay.
|
| ||||
| OK | |
| 7.INSPECT NO. 7 RELAY BLOCK (RELAY HOLDER TERMINAL VOLTAGE) |
![]() |
Remove the ST CUT relay from the No. 7 relay block.
Turn the ignition switch on (IG).
Measure the voltage between the terminals of the ST CUT relay holder.
| Tester Connection | Specified Condition |
| 1 - 2 | 10 to 14 V |
Reinstall the relay.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH START SWITCH OR PARK / NEUTRAL POSITION SWITCH ASSEMBLY - MAIN BODY ECU) |
![]() |
Remove the ST CUT relay from the No. 7 relay block.
Disconnect the A4 clutch start switch assembly connector (for M/T models).
Disconnect the B28 PNP switch assembly connector (for A/T models).
Disconnect the E20 main body ECU connector.
Disconnect the B32 ECM connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| ST CUT relay (3) - STAR (B32-52) | Below 1 Ω |
| ST CUT relay (3) - STR2 (E20-14) | Below 1 Ω |
| STR (E20-3) - ST CUT relay (5) | Below 1 Ω |
| B (A4-2)*1 - ST CUT relay (5) | Below 1 Ω |
| B (B28-4)*2 - ST CUT relay (5) | Below 1 Ω |
| Tester Connection | Specified Condition |
| ST CUT relay (3) - Body ground | 10 kΩ or higher |
| ST CUT relay (5) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the main body ECU connector.
Reconnect the clutch start switch assembly connector.
Reconnect the PNP switch assembly connector.
Reinstall the ST CUT relay.
|
| ||||
| OK | |
| 9.INSPECT NO. 7 RELAY BLOCK (CHECK FOR SHORT) |
![]() |
Disconnect the ECM connector.
Remove the ST CUT relay from the No. 7 relay block.
Measure the resistance between the terminals of the ST CUT relay holder.
| Tester Connection | Specified Condition |
| No. 7 Relay block ST CUT relay (3) - Body ground | 10 kΩ or higher |
| No. 7 Relay block ST CUT relay (5) - Body ground | 10 kΩ or higher |
Reinstall the ST CUT relay.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH OR PARK / NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY) |
![]() |
Remove the ST relay from the No. 7 relay block (for LHD).
Remove the ST relay from the No. 8 relay block (for RHD).
Disconnect the A4 clutch start switch assembly connector (for M/T models).
Disconnect the B28 PNP switch assembly connector (for A/T models).
Disconnect the A12 ECM connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| L (A4-1)*1 - STA (A12-48) | Below 1 Ω |
| L (A4-1)*1 - ST relay (1) | Below 1 Ω |
| L (B28-5)*2 - STA (A12-48) | Below 1 Ω |
| L (B28-5)*2 - ST relay (1) | Below 1 Ω |
| ST relay (2) - Body ground | Below 1 Ω |
| Tester Connection | Specified Condition |
| L (A4-1)*1 - Body ground | 10 kΩ or higher |
| L (B28-5)*2 - Body ground | 10 kΩ or higher |
Reinstall the ST relay.
Reconnect the clutch start switch connector.
Reconnect the PNP switch assembly connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 11.INSPECT BATTERY |
Check that the battery is not depleted.
|
| ||||
| OK | |
| 12.CHECK BATTERY TERMINAL |
Check that the battery terminals are not loose or corroded.
|
| ||||
| OK | ||
| ||