Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > TERMINALS OF ECU

for Preparation Click here



CHECK AIR CONDITIONING AMPLIFIER

E115964E04

  1. Measure the voltage and resistance of the connectors.

    HINT:
    Check from the rear of the connector while it is connected to the air conditioning amplifier.


    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    SOL+ (E41-2) - GND (E41-14)
    GR - W-B
    A/C compressor operation signal
    Engine idling
    Pulse generation
    (see waveform 1)
    Refrigerant pressure: normal
    Always
    Blower switch LO
    A/C switch ON
    PRE (E41-9) - SG-2 (E41-13)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (less than 0.196 MPa [2.0 kgf/cm2, 28 psi])
    Below 0.76 V
    PRE (E41-9) - SG-2 (E41-13)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (more than 3.14 MPa [32 kgf/cm2, 455 psi])
    4.74 V or higher
    BLW (E41-23) - GND (E41-14)
    R - W-B
    Blower motor control signal
    Ignition switch on (IG)
    Pulse generation
    (see waveform 2)
    Blower switch LO
    TSD (E41-33) - S5-4 (E41-31)
    L - LG
    Driver side solar sensor signal
    Ignition switch on (IG)
    0.8 to 4.3 V
    Solar sensor subject to electric light
    TSP (E41-32) - S5-4 (E41-31)
    P - LG
    Passenger side solar sensor signal
    Ignition switch on (IG)
    0.8 to 4.3 V
    Solar sensor subject to electric light
    TR (E41-29) - SG-1 (E41-34)
    GR- V
    Room temperature sensor signal
    Ignition switch on (IG)
    1.8 to 2.2 V
    Vehicle interior temperature: 25°C (77°F)
    SG-1 (E41-34) - Body ground
    V - Body ground
    Ground for room temperature sensor
    Always
    Below 1 V
    GND (E41-14) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1 V
    IG+ (E41-1) - GND (E41-14)
    Y - W-B
    Power source (IG)
    Ignition switch on (IG)
    10 to 14 V
    S5-3 (E41-10) - GND (E41-14)
    B - W-B
    Power supply for pressure sensor
    Ignition switch on (IG)
    4.5 to 5.5 V
    CANH (E41-11) - GND (E41-14)
    V - W-B
    Hi-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 3)
    CANL (E41-12) - GND (E41-14)
    W - W-B
    Lo-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 4)
    RDEF (E41-38) - GND (E41-14)
    B - W-B
    Rear defogger switch signal
    Ignition switch on (IG)
    Rear defogger switch OFF
    10 to 14 V
    RDEF (E41-38) - GND (E41-14)
    B - W-B
    Rear defogger switch signal
    Ignition switch on (IG)
    Rear defogger switch ON
    Below 1 V
    SG-2 (E41-13) - Body ground
    G - Body ground
    Ground for pressure sensor
    Always
    Below 1 V
    PTC1 (E41-3) - Body ground(*1)
    W - Body ground
    PTC NO. 1 heater relay operation signal
    Engine idling
    Below 1 V → 10 to 14 V
    Set temperature: MAX HOT
    Engine coolant temperature: Below 65°C (149°F)
    Ambient temperature: Below 10°C (50°F)
    Light control switch: OFF
    Blower switch OFF → LO
    PTC2 (E41-22) - Body ground(*1)
    B - Body ground
    PTC NO. 2 heater relay operation signal
    Engine idling
    Below 1 V → 10 to 14 V
    Set temperature: MAX HOT
    Engine coolant temperature: Below 65°C (149°F)
    Ambient temperature: Below 10°C (50°F)
    Light control switch: OFF
    Blower switch OFF → LO
    ALT (E41-25) - Body ground(*1)
    B - Body ground
    Generator signal
    Engine idling
    Pulse generation
    HLS (E41-27) - Body ground(*1)
    BR - Body ground
    Headlight signal
    Engine idling
    Below 1 V
    Light control switch: ON
    LIN1 (E41-37) - GND (E41-14)
    B - W-B
    LIN communication signal
    Ignition switch on (IG)
    Pulse generation
    LOCK (E41-8) - SG-2 (E41-13)(*2)
    W - G
    Compressor lock sensor signal
    Ignition switch on (IG)
    AUTO switch ON
    A/C switch ON
    Magnetic clutch ON
    Pulse generation
    (see waveform 5)
    MGC (E41-20) - GND (E41-14)(*2)
    V - W-B
    Magnetic clutch relay signal
    Ignition switch on (IG)
    Magnetic clutch OFF
    10 to 14 V
    MGC (E41-20) - GND (E41-14)(*2)
    V - W-B
    Magnetic clutch relay signal
    Ignition switch on (IG)
    Magnetic clutch ON
    Below 1.5 V
    BUB G (c1-2) - Body ground
    -
    Ground for BUS IC
    Always
    Below 1 V
    BUS (c1-3) - BUB G (c1-2)
    -
    BUS IC control signal
    Ignition switch on (IG)
    Pulse generation
    B BUS (c1-4) - BUB G (c1-2)
    -
    Power supply for BUS IC
    Ignition switch on (IG)
    11 to 13 V
    SGA (c1-5) - Body ground
    -
    Ground for evaporator temperature sensor
    Always
    Below 1 V
    TEA (c1-6) - SGA (c1-5)
    -
    Evaporator temperature sensor signal
    Ignition switch on (IG)
    1.4 to 1.8 V
    Evaporator temperature: 15°C (59°F)

    HINT:
    *1: w/ PTC heater
    *2: for 2GR-FE



  2. E074977E11
  3. Using an oscilloscope, measure the waveform 1.
    Compressor and pulley operation signal 
    Item
    Content
    Symbols (Terminal No.)
    SOL+ (E41-2) - GND (E41-14)
    Tool Setting
    5 V/DIV., 500 μsec./DIV.
    Condition
    Engine idling, Blower switch LO, A/C switch ON



  4. E103396E05
  5. Using an oscilloscope, measure the waveform 2.
    Blower motor control signal 
    Item
    Content
    Symbols (Terminal No.)
    BLW (E41-23) - GND (E41-14)
    Tool Setting
    1 V/DIV., 500 μsec./DIV.
    Condition
    Ignition switch on (IG), Blower switch LO

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.



  6. A086154E10
  7. Using an oscilloscope, measure the waveform 3.
    CAN communication signal 
    Item
    Content
    Symbols (Terminal No.)
    CANH (E41-11) - GND (E41-14)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.



  8. A086155E11
  9. Using an oscilloscope, measure the waveform 4.
    CAN communication signal 
    Item
    Content
    Symbols (Terminal No.)
    CANL (E41-12) - GND (E41-14)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.



  10. E127551E01
  11. Using an oscilloscope, measure the waveform 5.
    Compressor lock sensor signal 
    Item
    Content
    Symbols (Terminal No.)
    LOCK (E41-8) - SG-2 (E41-13)
    Tool Setting
    500 mV/DIV., 20 msec./DIV.
    Condition
    Ignition switch on (IG), AUTO switch ON, A/C switch ON, Magnetic clutch ON


CHECK AIR CONDITIONING CONTROL

E123518E02

  1. Measure the voltage and resistance of the connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IG+ (E26-2) - GND (E26-7)
    L - W-B
    Power source (IG)
    Ignition switch on (IG)
    10 to 14 V
    GND (E26-7) - Body ground
    W-B - Body Ground
    Ground for air conditioning control assembly
    Always
    Below 1 V
    LIN1 (E26-11) - GND (E26-7)
    B - W-B
    LIN communication signal
    Ignition switch on (IG)
    Pulse generation
    +B (E26-1) - GND (E26-7)
    R - W-B
    Power source (Back-up)
    Always
    10 to 14 V
    ACC (E26-8) - GND (E26-7)
    GR - W-B
    ACC power supply
    Ignition switch on (ACC)
    10 to 14 V