DTC B1651/33 Manual Cut off Switch Trouble |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1651/33 | When one of following conditions is met:
|
|

| 1.CHECK FOR DTC |
![]() |
Turn the ignition switch on (IG).
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the airbag cut-off switch.
|
| ||||
| OK | |
| 3.INSPECT AIRBAG CUT-OFF SWITCH |
![]() |
Disconnect the E68 passenger airbag manual cut-off switch connector.
Measure the resistance of the switch.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (PMC-) - 2 (PMC+) | OFF | 80 to 120 Ω |
| 1 (PMC-) - 2 (PMC+) | ON | 320 to 480 Ω |
|
| ||||
| OK | |
| 4.CHECK INSTRUMENT PANEL WIRE (FOR OPEN) |
![]() |
Disconnect the instrument panel wire connector from the airbag cut-off switch.
Using a service wire, connect E68-1 (PMC-) and E68-2 (PMC+) of connector C.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E49-11 (MSW+) - E49-12 (MSW-) | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK INSTRUMENT PANEL WIRE (FOR SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E49-11 (MSW+) - E49-12 (MSW-) | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK INSTRUMENT PANEL WIRE (TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| E49-11 (MSW+)- Body ground | Below 1 V |
| E49-12 (MSW-) - Body ground | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK INSTRUMENT PANEL WIRE (TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E49-11 (MSW+) - Body ground | 1 MΩ or higher |
| E49-12 (MSW-) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | |
| 8.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the connectors to the center airbag sensor and airbag cut-off switch.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||