Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

DTC    B2312    Driver Side Door Master Switch Malfunction

for Preparation Click here


DESCRIPTION

The driver door power window regulator motor is driven by operating the power window regulator master switch. The driver door power window regulator motor has motor, regulator, and ECU functions.
When the ECU determines that the power window regulator master switch is stuck, DTC B2312 is set.

NOTICE:
  1. The power window control system uses a multiplex communication system (LIN). Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
  2. When the power window regulator motor assembly (on the driver side) is reinstalled or replaced, the power window control system must be initialized.
  3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:
    1. Close the power window by fully pulling up the power window switch and holding it in the AUTO UP position.
    2. Open the power window by fully pushing down the switch.


DTC No.
DTC Detection Condition
Trouble Area
B2312
Power window regulator master switch stuck
  1. Power window regulator motor (on driver side)
  2. Power window regulator master switch
  3. Wire harness
  4. Power window regulator master switch held in same position for more than 20 seconds

WIRING DIAGRAM


E124603E03


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MASTER SWITCH)
  1. Using the Data List to check the function of the power window master switch.

    Power window regulator master switch 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    D P/W Auto SW
    Driver side power window
    AUTO switch signal / ON or OFF
    ON: Driver side power window AUTO switch operates
    OFF: Driver side power window AUTO switch does not operate
    -
    D P/W Up SW
    Driver side power window
    UP switch signal / ON or OFF
    ON: Driver side power window UP switch operates
    OFF: Driver side power window UP switch does not operate
    -
    D P/W Down SW
    Driver side power window
    DOWN switch signal / ON or OFF
    ON: Driver side power window DOWN switch operates
    OFF: Driver side power window DOWN switch does not operate
    -

    OK:
    ON (switch operates) appears on screen.

    HINT:
    When the power window operates normally, the problem has been caused by irregular switch operation (for example, the power window regulator master switch was held in the same position for more than 20 seconds).



OK
REPLACE POWER WINDOW REGULATOR MOTOR (for Driver Side)
NG


2.CHECK WIRE HARNESS (SWITCH INPUT POWER SUPPLY)
B119969E02
  1. Disconnect the H2*1 or G8*2 switch connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for LHD:
    Tester Connection
    Specified Condition
    H2-6 (B) - H2-1 (E)
    10 to 14 V
    for RHD:
    Tester Connection
    Specified Condition
    G8-6 (B) - G8-9 (E)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.CHECK WIRE HARNESS (MASTER SWITCH - REGULATOR MOTOR)


    E124617E02
  1. Disconnect the H2*1 or G8*2 switch connector.

  1. Disconnect the H4*1 or G9*2 motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    H2-8 (U) - H4-10 (UP)
    Below 1 Ω
    H2-5 (D) - H4-7 (DOWN)
    Below 1 Ω
    H2-4 (A) - H4-4 (AUTO)
    Below 1 Ω
    H2-3 (LED) - H4-5 (LED)
    Below 1 Ω
    for RHD:
    Tester Connection
    Specified Condition
    G8-1 (U) - G9-10 (UP)
    Below 1 Ω
    G8-5 (D) - G9-7 (DOWN)
    Below 1 Ω
    G8-4 (A) - G9-4 (AUTO)
    Below 1 Ω
    G8-3 (LED) - G9-5 (LED)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.REPLACE POWER WINDOW REGULATOR MASTER SWITCH
  1. Temporarily replace the power window regulator master switch with a new or normally functioning one.

  1. Check for DTC.

    OK:
    DTC is not output.



NG
REPLACE POWER WINDOW REGULATOR MOTOR (for Driver Side)
OK

END