Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Taillight Relay Circuit

for Preparation Click here


DESCRIPTION

When the light control switch, located on the headlight dimmer switch, is turned to the TAIL position, the taillight relay turns on to illuminate the front clearance lights, rear taillights and license plate light.

WIRING DIAGRAM


B255596E01


B118214E01


INSPECTION PROCEDURE

1.CHECK WHETHER LIGHTS ILLUMINATE
  1. Check whether the following lights illuminate: front clearance lights, rear taillights, license plate light.

    Result:

    Result
    Proceed to
    All lights do not illuminate
    A
    Front clearance lights do not illuminate
    B
    Rear taillights do not illuminate
    C
    License plate light does not illuminate
    D
    All lights illuminate
    E



B
Go to step 9

C
Go to step 11

D
Go to step 12

E
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A


2.INSPECT FUSE (TAIL)
  1. Remove the TAIL fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


3.CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY)
B118228E01
  1. Disconnect the IG instrument panel junction block connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    IG-1 - Body ground
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.CHECK INSTRUMENT PANEL JUNCTION BLOCK (T-LP RELAY)

E210001E01

  1. Disconnect the IG, IE and IS instrument panel connectors.

  1. Measure the resistance of the junction block.

    Standard resistance:
    Tester Connection
    Specified Condition
    IG-1 - IE-10
    10 kΩ or higher
    IG-1 - IE-10
    Below 1 Ω
    (Battery voltage applied to terminals IG-1 and IS-9)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
OK


5.CHECK WIRE HARNESS (MAIN BODY ECU - HEADLIGHT DIMMER SWITCH)

B128031E04

  1. Disconnect the E18 main body ECU connector.

  1. Disconnect the E15 headlight dimmer switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LH side 
    Tester Connection
    Specified Condition
    E18-21 (TAIL) - E15-18 (T)
    Below 1 Ω
    for RH side 
    Tester Connection
    Specified Condition
    E18-21 (TAIL) - E15-13 (T)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.CHECK WIRE HARNESS (HEADLIGHT DIMMER SWITCH - BATTERY)
B128029E01
  1. Connect the E18 main body ECU connector.

  1. Disconnect the E15 headlight dimmer switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for LH side 
    Tester Connection
    Specified Condition
    E15-18 (T) - Body ground
    11 to 14 V
    for RH side 
    Tester Connection
    Specified Condition
    E15-13 (T) - Body ground
    11 to 14 V



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
OK


7.CHECK WIRE HARNESS (HEADLIGHT DIMMER SWITCH - BODY GROUND)
B128029E03
  1. Disconnect the E15 headlight dimmer switch connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LH side 
    Tester Connection
    Specified Condition
    E15-12 (EL) - Body ground
    Below 1 Ω
    for RH side 
    Tester Connection
    Specified Condition
    E15-19 (EL) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8.INSPECT HEADLIGHT DIMMER SWITCH
B128006E15
  1. Remove the headlight dimmer switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    for LH side 
    Tester Connection
    Switch Condition
    Specified Condition
    18 (T) - 12 (EL)
    Light control switch OFF
    10 kΩ or higher
    18 (T) - 12 (EL)
    Light control switch TAIL
    Below 1 Ω
    for RH side 
    Tester Connection
    Switch Condition
    Specified Condition
    13 (T) - 19 (EL)
    Light control switch OFF
    10 kΩ or higher
    13 (T) - 19 (EL)
    Light control switch TAIL
    Below 1 Ω



NG
REPLACE HEADLIGHT DIMMER SWITCH
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) 

9.CHECK INSTRUMENT PANEL JUNCTION BLOCK (TAILLIGHT RELAY)
B135270E05
  1. Disconnect the IB instrument panel junction block connectors.

  1. Measure the voltage of the junction block.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Junction block IB terminal 15 - Body ground
    Light control switch TAIL
    11 to 14 V
    Junction block IB terminal 33 - Body ground



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
OK


10.CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - FRONT CLEARANCE LIGHT AND BODY GROUND)


    E209998E01
  1. w/ Hood Moulding:

    1. Disconnect the A75 and A76 front clearance light connectors.

    2. Measure the voltage and resistance of the wire harness side connectors.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      A75-2 - Body ground
      Light control switch TAIL
      11 to 14 V
      A76-2 - Body ground
      Light control switch TAIL
      11 to 14 V

      Standard resistance:
      Tester Connection
      Specified Condition
      A75-1 - Body ground
      Below 1 Ω
      A76-1 - Body ground
      Below 1 Ω



    B128032E02
  1. w/o Hood Moulding:

    1. Disconnect the A20 and A33 front clearance light connectors.

    2. Measure the voltage and resistance of the wire harness side connectors.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      A20-2 - Body ground
      Light control switch TAIL
      11 to 14 V
      A33-2 - Body ground
      Light control switch TAIL
      11 to 14 V

      Standard resistance:
      Tester Connection
      Specified Condition
      A20-1 - Body ground
      Below 1 Ω
      A33-1 - Body ground
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE FRONT CLEARANCE LIGHT BULB 

11.CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - REAR COMBINATION LIGHT)
B123802E09
  1. Disconnect the K13 and K15 rear combination light connectors.

  1. Measure the voltage and resistance of the wire harness side connectors.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    K15-2 - Body ground
    Light control switch TAIL
    11 to 14 V
    K13-2 - Body ground
    Light control switch TAIL
    11 to 14 V

    Standard resistance:
    Tester Connection
    Specified Condition
    K15-1 - Body ground
    Below 1 Ω
    K13-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE REAR COMBINATION LIGHT 

12.CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - LICENSE PLATE LIGHT AND BODY GROUND)


    B128088E01
  1. w/o Tire Carrier:

    1. Disconnect the S6 license plate light connector.

    2. Measure the voltage and resistance of the wire harness side connector.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      S6-1 - Body ground
      Light control switch TAIL
      11 to 14 V

      Standard resistance:
      Tester Connection
      Specified Condition
      S6-2 - Body ground
      Below 1 Ω



    B128033E04
  1. w/o Rear Fog Light (One Piece Type):

    1. Disconnect the S6 license plate light connector.

    2. Measure the voltage and resistance of the wire harness side connector.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      S6-2 - Body ground
      Light control switch TAIL
      11 to 14 V

      Standard resistance:
      Tester Connection
      Specified Condition
      S6-1 - Body ground
      Below 1 Ω



    B128033E06
  1. w/o Rear Fog Light (Two Piece Type):

    1. Disconnect the N3 license plate light connector.

    2. Measure the voltage and resistance of the wire harness side connector.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      N3-2 - Body ground
      Light control switch TAIL
      11 to 14 V

      Standard resistance:
      Tester Connection
      Specified Condition
      N3-1 - Body ground
      Below 1 Ω



    B128033E03
  1. w/ Tire Carrier (w/ Rear Fog Light):

    1. Disconnect the N2 license plate light connector.

    2. Measure the voltage and resistance of the wire harness side connector.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      N2-2 - Body ground
      Light control switch TAIL
      11 to 14 V

      Standard resistance:
      Tester Connection
      Specified Condition
      N2-1 - Body ground
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE LICENSE PLATE LIGHT BULB