Home › ENGINE · 2GR-FE › IGNITION › IGNITION SYSTEM

IGNITION SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. CHECK IGNITION COIL ASSEMBLY AND PERFORM SPARK TEST

NOTICE:
In this section, the terms "Cold" and "Hot" refer to the temperature of the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).

  1. Check the DTCs.

    NOTICE:
    If a DTC is present, perform troubleshooting in accordance with the procedure for that DTC.



  1. Check that sparks occur.

    1. Remove the V-bank cover.



    2. A170857
    3. Disconnect the throttle body connector.



    4. A170856
    5. Remove the 4 bolts then separate the throttle body.

    6. Remove the intake air surge tank (Click here).

    7. Remove the bolt and ignition coil.

    8. Using a 16 mm spark plug wrench, remove the spark plugs.



    9. A136823
    10. Disconnect the 6 fuel injector connectors.



    11. A136826
    12. Install the spark plug into the ignition coil, and then connect the ignition coil connectors.

    13. Ground the spark plug.

    14. Check that spark occurs at the spark plug while the engine is being cranked.

      NOTICE:
      1. Be sure to ground the spark plugs when checking them.
      2. If an ignition coil has been struck or dropped, replace it.
      3. Do not crank the engine for more than 2 seconds.

      If spark does not occur, perform the following steps.

    15. Using a 16 mm plug wrench, install the spark plug.

      Torque:
      18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    16. Install the ignition coil with the bolt.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    17. Connect the 6 fuel injector connectors.

    18. Install the intake air surge tank (Click here).

    19. Install the V-bank cover.



  1. Perform troubleshooting using the following steps.

    1. Check that the ignition coil connectors are securely connected.

      Result:
      Result
      Action
      NG
      Connect securely
      OK
      Go to next step

    2. Perform a spark test on each ignition coil.

      1. Replace the ignition coil with a known good one as necessary.
      2. Perform the spark test again.

      Result:
      Result
      Action
      OK
      Replace ignition coil
      NG
      Go to next step



    3. A136824
    4. Check the power supply to the ignition coil.

      1. Disconnect the ignition coil connector.
      2. Turn the ignition switch on (IG).
      3. Measure the voltage of the wire harness side connector.

      Standard voltage:
      Tester Connection
      Specified Condition
      1 (+B) - 4 (GND)
      9 to 14 V

      Result:
      Result
      Action
      NG
      Check wire harness and connector
      OK
      Go to next step

    5. Check the resistance of the crankshaft position sensor.

      Standard resistance:
      Temperature Condition
      Specified Condition
      Cold
      1630 to 2740 Ω
      Hot
      2065 to 3225 Ω

      Result:
      Result
      Action
      NG
      Replace crankshaft position sensor
      OK
      Go to next step

    6. Check the IGT signal from the ECM.

      Result:
      Result
      Action
      NG
      Check ECM (Click here)
      OK
      Repair wiring between ignition coil and ECM



2. CHECK SPARK PLUG


    I039522E10
  1. Check the electrode using a megohmmeter:

    1. Using a megohmmeter, measure the insulation resistance.

      Standard insulation resistance:
      10 MΩ or more

      If the result is below 10 MΩ, clean the plug and measure the resistance again.

  1. Check the electrode without using a megohmmeter:

    1. Quickly accelerate the engine to 4,000 rpm 5 times.

    2. Remove the spark plug.

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage on its threads and insulator.
    If there is damage, replace the spark plug.

    Recommended spark plug:
    Manufacturer
    Spark plug type
    DENSO
    FK20HR11



    A175269E01
    B062019E01
  1. Check the spark plug electrode gap.

    Maximum electrode gap for used spark plug:
    1.4 mm (0.055 in.)

    If the gap is greater than the maximum, replace the spark plug.

    Electrode gap for new spark plug:
    1.0 to 1.1 mm (0.039 to 0.043 in.)

    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Standard air pressure:
    588 kPa (6 kgf/cm2, 85 psi)

    Standard duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.