ENGINE OIL COOLER (w/ Oil Cooler) > INSTALLATION |
| 1. INSTALL ENGINE OIL COOLER |
Clean the oil cooler contact surface on the cooler mounting.
![]() |
Install a new O-ring to the oil cooler.
Apply a light coat of engine oil on the threads and under the head of the union bolt.
![]() |
Install the oil cooler with the plate washer, nut and union bolt.
Connect the 2 oil cooler hoses.
| 2. INSTALL OIL FILTER SUB-ASSEMBLY |
Check and clean the oil filter installation surface.
Apply clean engine oil to the gasket of a new oil filter.
![]() |
Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.
Using SST, tighten the oil filter.
Depending on the work space available, choose from the following.
1. If enough space is available, use a torque wrench to tighten the oil filter.
| 3. INSTALL NO. 1 ENGINE UNDER COVER |
| 4. ADD ENGINE OIL |
Clean and install the oil drain plug with a new gasket.
Add new oil.
| Item | Specified Condition |
| Drain and refill with oil filter change | 4.2 liters (4.4 US qts, 3.7 Imp. qts) |
| Drain and refill without oil filter change | 4.0 liters (4.2 US qts, 3.5 Imp. qts) |
| Dry fill | 4.9 liters (5.2 US qts, 4.3 Imp. qts) |
Install the oil filler cap.
| 5. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.
![]() |
Continue adding TOYOTA SLLC until it is filled to the B line at the base of the reservoir's filler neck.
| Item | Specified Condition |
| A/T | 6.4 liters (6.8 US qts, 5.6 Imp. qts) |
| M/T | 6.3 liters (6.7 US qts, 5.5 Imp. qts) |
Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant. If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Start the engine and warm it up until the cooling fan operates. While the cooling fan operates, circulate the coolant for several minutes.
Set the air conditioning as follows while warming up the engine.
| Item | Specified Condition |
| Manual Air Conditioning System | Fan speed: Any setting except OFF |
| Temperature: Toward WARM Air conditioning switch: OFF | |
| Automatic Air Conditioning System | Temperature: Toward MAX Air conditioning switch: OFF |
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW line.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.
| 6. CHECK FOR ENGINE COOLANT LEAKS |
Check for engine coolant leaks (Click here).
| 7. CHECK ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait for 5 minutes.
Check that the engine oil level is between the L and F marks, of the oil dipstick.
If low, check for leakage and add oil up to the F mark.