ENGINE > ON-VEHICLE INSPECTION |
| 1. INSPECT ENGINE COOLANT |
| 2. INSPECT ENGINE OIL |
| 3. INSPECT BATTERY |
| 4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner cap.
Remove the air filter element.
Visually check that the air filter is not excessively damaged or oily.
If necessary, replace the air cleaner filter element sub-assembly.
| 5. INSPECT SPARK PLUG |
| 6. INSPECT FAN AND GENERATOR V BELT |
| 7. INSPECT IGNITION TIMING |
Warm up and stop the engine.
![]() |
When using intelligent tester:
Connect the intelligent tester to the DLC3.
Allow the engine to idle.
Select the following menu items:
Powertrain / Engine and ECT / Data List / IGN Advance.
Read IGN Advance to check the ignition timing.
Check that the ignition timing advances immediately when the engine speed is increased.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using intelligent tester:
Remove the No. 1 engine cover .
![]() |
Open the ignition cover located to the right of the No. 4 ignition coil.
Pull out the wire harness from the IG cover.
Connect a timing light to the wire harness.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Allow the engine to idle and check the ignition timing.
Remove SST from the DLC3.
Allow the engine to idle and check the ignition timing.
Check that the ignition timing advances immediately when the engine speed is increased.
Turn the ignition switch off.
Remove the timing light.
Close the IG cover.
Install the No. 1 engine cover .
| 8. INSPECT ENGINE IDLE SPEED |
![]() |
When using intelligent tester:
Turn OFF all the accessories and air conditioning.
Move the shift lever to P or neutral.
Connect the intelligent tester to the DLC3.
Warm up the engine.
Select the tester menus:
Powertrain / Engine and ECT / Data List / Engine SPD
Read Engine SPD to check the idle speed while the radiator-cooling fan is not rotating.
| Item | Specified Condition |
| A/T vehicle | 610 to 710 rpm |
| M/T vehicle | 650 to 750 rpm |
Turn the ignition switch off.
Disconnect the tester from the DLC3.
![]() |
When not using intelligent tester:
Turn OFF all the accessories and air conditioning.
Move the shift lever to P or neutral.
Connect SST to 9 (TAC) of the DLC3 terminal, and then connect a tachometer to SST.
Warm up the engine.
Check the idle speed while the radiator-cooling fan is not rotating.
| Item | Specified Condition |
| A/T vehicle | 610 to 710 rpm |
| M/T vehicle | 650 to 750 rpm |
Turn the ignition switch off.
Remove the tachometer and disconnect SST from the DLC3.
| 9. INSPECT COMPRESSION |
Warm up and stop the engine.
Remove the No. 1 engine under cover.
Remove the 4 ignition coils .
Remove the 4 spark plugs.
Disconnect the 4 fuel injector connectors.
![]() |
Insert a compression gauge into the spark plug hole.
While cranking the engine, measure the compression pressure.
Connect the 4 fuel injector connectors.
Install the 4 spark plugs.
Install the 4 ignition coils .
Install the No. 1 engine under cover.
| 10. INSPECT CO/HC |
Start and warm up the engine.
Run the engine at 2,500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe while idling.
Inspect the CO/HC concentration while idling and/or at 2,500 rpm.
If the CO/HC concentration is not as specified, perform troubleshooting.
| CO | HC | Problems | Causes |
| Normal | High | Rough idle | 1. Faulty ignition: - Incorrect timing - Plugs are contaminated, shorted, or gaps are defective 2. Incorrect valve clearance 3. Leaks in intake and exhaust valve 4. Leaks in cylinders |
| Low | High | Rough idle (Fluctuating HC reading) | 1. Vacuum leakage: - Ventilation hoses - Intake manifold - Throttle body - Brake booster line 2. Lean mixture causing misfire |
| High | High | Rough idle (Black smoke from exhaust) | 1. Restricted air filter 2. Plugged PCV valve 3. Faulty SFI system: - Faulty pressure regulator - Faulty engine coolant temperature sensor - Faulty mass air flow meter - Faulty ECM - Faulty injectors - Faulty throttle body |