Home › BODY › INSTRUMENT PANEL › UPPER INSTRUMENT PANEL

UPPER INSTRUMENT PANEL > REMOVAL

for Preparation Click here



1. TABLE OF BOLT, SCREW AND NUT


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet codes in the table below.



B208880E02



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
w/ Navigation System (for HDD):
After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



3. REMOVE STEERING WHEEL PAD ASSEMBLY
  1. for 1AZ-FE, 2AZ-FE:
    Remove the steering wheel pad assembly (Click here).

  1. for 3ZR-FAE:
    Remove the steering wheel pad assembly .



4. REMOVE STEERING WHEEL ASSEMBLY (for LHD)


    C195901E01
  1. Remove the nut and place matchmarks on the steering wheel and steering column.



    C195902E01
  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



5. REMOVE STEERING WHEEL ASSEMBLY (for RHD)


    C203467E01
  1. Remove the nut and place matchmarks on the steering wheel and steering column.



    C203468E01
  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



6. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


B129872
  1. Using a screwdriver, detach the 4 clips and 6 claws, and then remove the instrument cluster finish panel.

    HINT:
    Tape the screwdriver tip before use.



7. REMOVE COMBINATION METER ASSEMBLY


B136780
  1. Remove the 2 screws.

  1. Pull the combination meter in the direction indicated by the arrow in the illustration to detach the 2 clips.

  1. Disconnect the connector and remove the combination meter.



8. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL CENTER


    B208365
  1. Using a moulding remover, detach the 3 clips and 2 claws, and then remove the cluster finish panel.

  1. Disconnect the connector.



9. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL CENTER


    B208366
  1. Using a moulding remover, detach the 3 clips and 2 claws, and then remove the cluster finish panel.

  1. Disconnect the connector.



10. REMOVE STEREO OPENING COVER WITH BRACKET (w/o Radio Receiver)


B133002
  1. Remove the 4 bolts.

  1. Detach the 4 clips and remove the stereo opening cover.



11. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)
  1. for 3ZR-FAE:
    Remove the radio receiver assembly with bracket .

  1. except 3ZR-FAE
    Remove the radio receiver assembly with bracket .



12. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
  1. for DVD:
    Remove the navigation receiver assembly with bracket .

  1. for HDD:
    Remove the navigation receiver assembly with bracket .



13. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY CENTER


    B129890
  1. Using a moulding remover, detach the 5 clips and remove the instrument panel register.



14. REMOVE FRONT PILLAR GARNISH LH
  1. for Short Body:
    Remove the front pillar garnish .

  1. for Long Body:
    Remove the front pillar garnish .



15. REMOVE FRONT PILLAR GARNISH RH
  1. for Short Body:
    Remove the front pillar garnish .

  1. for Long Body:
    Remove the front pillar garnish .



16. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B129889E04
  1. Open the glove compartment door.

  1. Detach the claw from the glove compartment door stopper.

  1. While pushing in the sides of the glove compartment door in the direction indicated by the arrows in the illustration, open the door to release it from the 2 stoppers.



    B129888
  1. Open the door as much as possible.

  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.



17. REMOVE UPPER INSTRUMENT PANEL


    B129886
  1. Remove the 2 bolts from the passenger airbag.

  1. Disconnect the passenger airbag connector.

  1. Remove the 2 bolts and 2 screws.

  1. Disconnect the connector and detach the clamp.



  1. Detach the 6 clips and 5 claws and remove the instrument panel.


    B208364