Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > ECM Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
Either condition is met:
  1. "Engine" is not displayed on "Bus Check".
  2. "ECM Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside ECM
  2. Harness or connector
  3. ECM

WIRING DIAGRAM


C203429E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)


  1. Disconnect the A12, B32*1, *2 and B96*3 ECM connectors.

    1. *1: for 1AZ-FE, 2AZ-FE
    2. *2: for 3ZR-FAE
    3. *3: for 2GR-FE

    C203630E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1AZ-FE, 2AZ-FE:
    Tester Connection
    Condition
    Specified Condition
    B32-104 (E1) - Body ground
    Always
    Below 1 Ω
    B32-45 (E01) - Body ground
    Always
    Below 1 Ω
    B32-44 (E02) - Body ground
    Always
    Below 1 Ω
    B32-86 (E03) - Body ground
    Always
    Below 1 Ω
    B32-46 (E04) - Body ground
    Always
    Below 1 Ω
    B32-43 (ME01) - Body ground
    Always
    Below 1 Ω
    for 3ZR-FAE:
    Tester Connection
    Condition
    Specified Condition
    B32-105 (E1) - Body ground
    Always
    Below 1 Ω
    B32-46 (E01) - Body ground
    Always
    Below 1 Ω
    B32-45 (E02) - Body ground
    Always
    Below 1 Ω
    B32-81 (E03) - Body ground
    Always
    Below 1 Ω
    B32-41 (E04) - Body ground
    Always
    Below 1 Ω
    B32-44 (ME01) - Body ground
    Always
    Below 1 Ω
    for 2GR-FE:
    Tester Connection
    Condition
    Specified Condition
    B96-81 (E1) - Body ground
    Always
    Below 1 Ω
    B96-22 (E01) - Body ground
    Always
    Below 1 Ω
    B96-21 (E02) - Body ground
    Always
    Below 1 Ω
    B96-104 (E03) - Body ground
    Always
    Below 1 Ω
    B96-23 (E04) - Body ground
    Always
    Below 1 Ω
    B96-20 (ME01) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 1AZ-FE, 2AZ-FE, 2GR-FE:
    Tester Connection
    Switch Condition
    Specified Condition
    A12-1 (+B2) - Body ground
    Battery's positive (+) voltage applied to terminal MREL
    11 to 14 V
    A12-2 (+B) - Body ground
    Battery's positive (+) voltage applied to terminal MREL
    11 to 14 V
    A12-3 (+BM) - Body ground
    Always
    11 to 14 V
    A12-20 (BATT) - Body ground
    Always
    11 to 14 V
    A12-28 (IGSW) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    for 3ZR-FAE:
    Tester Connection
    Switch Condition
    Specified Condition
    A12-1 (+B2) - Body ground
    Battery's positive (+) voltage applied to terminal MREL
    11 to 14 V
    A12-2 (+B) - Body ground
    Battery's positive (+) voltage applied to terminal MREL
    11 to 14 V
    A12-3 (+BM) - Body ground
    Always
    11 to 14 V
    A12-20 (BATT) - Body ground
    Always
    11 to 14 V
    A12-27 (IGSW) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM