Home › BODY › EXTERIOR › FRONT BUMPER (w/o Under Guard)

FRONT BUMPER (w/o Under Guard) > REASSEMBLY

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


  1. w/o Under Guard, w/ Under Guard:



      E179677
    1. Attach the 2 claws to install the headlight washer actuator sub-assembly.



    2. E179680
    3. Install the headlight washer actuator with the 2 screws.



  1. w/ Hood Moulding:



      E208569
    1. Attach the claw to install the headlight washer actuator sub-assembly with the headlight cleaner clamp as shown in the illustration.



    2. E208565
    3. Attach the 2 claws as shown in the illustration.



    4. E208566
    5. Push up the headlight cleaner clamp B to the surface of the bumper.



    6. E208567E01
    7. Install the headlight washer actuator sub-assembly with the clamp as shown in the illustration.
      Text in Illustration 
      *1
      Clamp
      *2
      Headlight Washer Actuator Sub-assembly LH
      *3
      Headlight Cleaner Clamp
      V100155
      Push Here



2. INSTALL HEADLIGHT WASHER, ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.



3. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    E179681
  1. Attach the 2 claws to install the headlight washer nozzle.



4. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.



5. INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)


  1. w/o Under Guard:



      E179678
    1. Attach the 5 clamps to install the hose to the front bumper.

    2. Connect the clamp to the headlight washer hose.



  1. w/ Under Guard:



      E179679
    1. Attach the 5 clamps to install the hose to the front bumper.

    2. Connect the clamp to the headlight washer hose.



  1. w/ Hood Moulding:



      E208561
    1. Attach the 6 clamps to install the hose to the front bumper.

    2. Connect the clamp to the headlight washer hose.



6. INSTALL FRONT BUMPER EXTENSION LH (w/ Outside Moulding)


B208471
  1. Attach the 6 clips to install the extension.

  1. Install the screw.



7. INSTALL FRONT BUMPER EXTENSION RH (w/ Outside Moulding)

HINT:
Use the same procedure described for the LH side.



8. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)


B208469
  1. Attach the 2 guides to install the fog light.

  1. Install the screw.



9. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure described for the LH side.



10. INSTALL FRONT BUMPER HOLE COVER LH


  1. Attach the 4 claws to install the bumper hole cover.


    B209238E01



11. INSTALL FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure described for the LH side.



12. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET


B208327
  1. Attach the 2 claws to install the mounting bracket.

  1. Install the 2 screws.



13. INSTALL FRONT BUMPER BAR
  1. Clean the bumper cover surface.

    1. Using a heat light, heat the bumper cover surface.

      Standard:
      Item
      Temperature
      Bumper cover
      20 to 30°C (68 to 86°F)

      NOTICE:
      Do not heat the bumper cover excessively.

    2. Remove the double-sided tape from the bumper cover.

    3. Wipe off any tape adhesive residue with cleaner.

  1. If reusing the bumper bar, clean the bumper bar.

    1. Remove the double-sided tape from the bumper bar.

    2. Wipe off any tape adhesive residue with cleaner.

    3. Apply new double-sided tape to the bumper bar.



    B209247E01
  1. Install the bumper bar.

    1. Using a heat light, heat the bumper cover and bumper bar.

      Standard:
      Item
      Temperature
      Bumper cover
      20 to 30°C (68 to 86°F)
      Bumper bar
      20 to 30°C (68 to 86°F)

      NOTICE:
      Do not heat the bumper cover and bumper bar excessively.

    2. Remove the peeling paper from the face of the bumper bar.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Install the bumper bar.

      HINT:
      Press the bumper bar firmly to install it.



14. INSTALL FRONT BUMPER ARM EXTENSION LH


B208465
  1. Attach the claw to install the arm extension.

  1. Install the screw and clip.



15. INSTALL FRONT BUMPER ARM EXTENSION RH

HINT:
Use the same procedure described for the LH side.



16. INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM


B208333
  1. Attach the 3 claws to install the emblem.



17. INSTALL LOWER NO. 2 RADIATOR GRILLE


B208463
  1. Attach the 12 claws and 3 guides to install the lower No. 2 radiator grille.



18. INSTALL LOWER NO. 1 RADIATOR GRILLE


B208462
  1. Attach the 16 claws to install the lower No. 1 radiator grille.



19. INSTALL RADIATOR GRILLE SUB-ASSEMBLY


B208460
  1. Attach the 7 claws and guide to install the radiator grille.



    B208461
  1. Install the 3 bolts and 3 nuts.



20. INSTALL HOOD TO RADIATOR GRILLE SEAL
  1. Clean the bumper cover surface.

    1. Using a heat light, heat the bumper cover surface.

      Standard:
      Item
      Temperature
      Bumper cover
      20 to 30°C (68 to 86°F)

      NOTICE:
      Do not heat the bumper cover excessively.

    2. Remove the double-sided tape from the bumper cover.

    3. Wipe off any tape adhesive residue with cleaner.



    B208348E01
  1. Install a new hood to radiator grille seal.

    1. Using a heat light, heat the bumper cover and hood to radiator grille seal.

      Standard:
      Item
      Temperature
      Bumper cover
      20 to 30°C (68 to 86°F)
      Hood to radiator grille seal
      20 to 30°C (68 to 86°F)

      NOTICE:
      Do not heat the bumper cover and hood to radiator grille seal excessively.

    2. Attach the 9 clips to install the hood to radiator grille seal.

    3. Install the 4 clips.

    4. Remove the peeling paper from the face of the hood to radiator grille seal.

    5. Attach the double-sided tape on the hood to radiator grille seal to the bumper cover.

      HINT:
      Press the hood to radiator grille seal firmly to install it.