Home › TRANSMISSION ยท U140F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


D009644E03
  1. Remove the nut, washer and control shaft lever.



    D009643E02
  1. Using a screwdriver, pry off the lock plate.

  1. Remove the nut and lock plate.



    D009639E02
  1. Remove the 2 bolts and pull out the switch.



2. REMOVE BREATHER PLUG HOSE


3. REMOVE OIL COOLER OUTLET TUBE UNION


C127809
  1. Remove the union.

  1. Remove the O-ring from the union.



4. REMOVE OIL COOLER INLET TUBE UNION


C126599
  1. Remove the union.

  1. Remove the O-ring from the union.



5. REMOVE SPEED SENSOR


D003900E01
  1. Remove the 2 bolts and 2 transmission revolution sensors from the transaxle.

  1. Remove the 2 O-rings from the sensors.



6. REMOVE NO. 1 TRANSAXLE CASE PLUG


C134982
  1. Remove the 4 plugs from the transaxle.

  1. Remove the 4 O-rings from the 4 plugs.



7. PLACE TRANSAXLE ON WOODEN BLOCKS


D009176E01


8. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


D009177E01
  1. Remove the 18 bolts.

  1. Remove the oil pan and 3 magnets.

  1. Remove the gasket from the oil pan.



9. INSPECT AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


AT00103E01
  1. Remove the magnets and use them to collect any steel chips. Examine the chips and particles in the pan and on the magnet to determine what type of wear has occurred in the transaxle.
    Steel (magnetic): bearing gear and plate wear
    Brass (non-magnetic): bush wear



10. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


D009179E04
  1. Remove the 3 bolts and oil strainer.



    D009180E01
  1. Remove the O-ring from the oil strainer.



11. REMOVE TRANSMISSION WIRE


C130917E01
  1. Disconnect the 5 shift solenoid valve connectors.

  1. Remove the bolt, lock plate and ATF temperature sensor.



    D003547E08
  1. Remove the bolt and transaxle wire.



    D003636E04
  1. Remove the O-ring from the transaxle wire.



12. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


D003553E01
  1. Support the valve body and remove the 17 bolts and valve body.



13. REMOVE NO. 1 GOVERNOR APPLY GASKET


C083127E01
  1. Remove the governor apply gasket from the transaxle case.



14. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET


C083128E01
  1. Remove the 2nd brake gasket from the transaxle.



15. REMOVE BRAKE DRUM GASKET


C083129E01
  1. Remove the brake drum gasket from the transaxle.



16. REMOVE CHECK BALL BODY


D003554E02
  1. Remove the check ball and spring from the transaxle.



17. REMOVE C-3 ACCUMULATOR PISTON


D003555E01
  1. Remove the spring from the C-3 accumulator piston.



    D003556E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.



    D003902E02
  1. Remove the O-ring from the C-3 accumulator piston.



18. REMOVE C-1 ACCUMULATOR PISTON


D003557E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-1 accumulator piston and spring.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.



    D003903E01
  1. Remove the 2 O-rings from the C-1 accumulator piston.



19. REMOVE B-3 ACCUMULATOR PISTON


D003558E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-3 accumulator piston and 2 springs.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.



    D003904E05
  1. Remove the O-ring from the B-3 accumulator piston.



20. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY


D003560E03
  1. Remove the 2 bolts, manual detent spring and cover.



21. REMOVE PARKING LOCK PAWL BRACKET


C056727E01
  1. Remove the 2 bolts and parking lock pawl bracket.



22. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING


D003559E01
  1. Using needle-nose pliers, remove the retainer spring.



23. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


C127824
  1. Using a chisel and hammer, unstake and remove the spacer.



    D003564E01
  1. Using a pin punch and hammer, tap out the pin.

    HINT:
    Slowly tap out the pin so that it will not fall into the transaxle.



    D003565E02
  1. Remove the manual valve lever shaft and manual valve lever.



24. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


D003905E01
  1. Remove the parking lock rod from the manual valve lever.



25. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


D003566E02
  1. Using a screwdriver, pry out the oil seal from the transaxle.



26. FIX AUTOMATIC TRANSAXLE ASSEMBLY
  1. Fix the transaxle case with the oil pump side facing up.



27. INSPECT INPUT SHAFT END PLAY


D008046E01
  1. Using a dial indicator, measure the input shaft end play.

    Standard end play:
    0.262 to 1.249 mm (0.0103 to 0.0492 in.)



28. REMOVE NO. 1 TRANSAXLE CASE PLUG


C134983
  1. Remove the 2 plugs.

  1. Remove the 2 O-rings from the 2 plugs.



29. REMOVE TRANSAXLE HOUSING


C126600
  1. Remove the 16 bolts.

  1. Tap on the circumference of the transaxle housing with a plastic-faced hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential may be accidentally removed when the transaxle housing is removed.



30. REMOVE OIL PUMP ASSEMBLY


D003569E07
  1. Remove the 7 bolts and oil pump from the transaxle.



31. REMOVE THRUST NEEDLE ROLLER BEARING


D025505E03
  1. Remove thrust needle roller bearing from the underdrive planetary gear.



32. REMOVE NO. 2 THRUST BEARING UNDERDRIVE RACE


D025506E04
  1. Remove the thrust bearing underdrive race from the underdrive planetary gear.



33. REMOVE DIFFERENTIAL GEAR ASSEMBLY


D003577E01
  1. Remove the differential gear form the transaxle.



34. REMOVE OVERDRIVE BRAKE GASKET


D003573E01
  1. Remove the 2 overdrive brake gaskets from the transaxle.



35. REMOVE FORWARD CLUTCH ASSEMBLY


D003574E03
  1. Remove the forward clutch from the transaxle.



    D003906E02
  1. Remove the thrust bearing from the forward clutch.



36. REMOVE MULTIPLE DISC CLUTCH HUB


D003575E01
  1. Remove the thrust bearing, multiple clutch hub, needle roller bearing and bearing race from the transaxle.



37. INSPECT MULTIPLE DISC CLUTCH HUB


D003829E03
  1. Using a caliper gauge, measure the inside diameter of the forward clutch hub bushing.

    Standard inside diameter:
    23.025 to 23.045 mm (0.9065 to 0.9073 in.)

    Maximum inside diameter:
    23.09 mm (0.9091 in.)

    NOTICE:
    1. When the diameter is over the maximum, replace the multiple disc clutch hub with a new one.
    2. Check the contact surface of the bush in the direct clutch shaft. If any scratch or discolor is identified, replace the direct clutch sub-assembly with a new one.

    If the inside diameter is greater then the maximum, replace the forward clutch hub.



38. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY


D003576E03
  1. Remove the bolt and parking pawl shaft clamp.



    D009652E01
  1. Remove the parking lock pawl shaft.



    D009689E01
  1. Push the parking lock pawl.

    HINT:
    Failure to do so will cause interference when the underdrive planetary gear is removed.



    D003579E04
  1. Remove the underdrive planetary gear from the transaxle.

    NOTICE:
    Be careful so that the underdrive planetary gear assembly will not fall out.



    D009690E01
  1. Remove the spring, pawl pin and parking lock pawl.



39. REMOVE UNDERDRIVE CLUTCH ASSEMBLY


D003580E02
  1. Remove the underdrive clutch, thrust bearing and bearing race from the transaxle.



40. REMOVE UNDERDRIVE 1-WAY CLUTCH ASSEMBLY


D003581E02
  1. Using a screwdriver, pry out the snap ring from the transaxle.



    D003627E03
  1. Remove the 1-way clutch from the transaxle.



    D003907E02
  1. Remove the outer race retainer from the 1-way clutch.



41. REMOVE NO. 2 UNDERDRIVE CLUTCH DISC


    D008050E01
  1. Using a screwdriver, pry out the snap ring.



    D009197E01
  1. Remove the flange, 3 discs and 3 plates from the transaxle.



42. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC


D009196E01
  1. Check to see if the sliding surface of the disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc is peeling off or discolored, or even if a part of the groove is defaced, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.



43. REMOVE UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


D003610E01
  1. Using SST, a snap ring expander and press, remove the snap ring and piston return spring.

    SST
    09387-00020  



44. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


D003806E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    14.04 mm (0.5528 in.)



45. REMOVE NO. 1 TRANSAXLE CASE PLUG


C134984
  1. Remove the 2 plugs from the transaxle rear cover.

  1. Remove the 2 O-rings from the 2 plugs.



46. REMOVE TRANSAXLE REAR COVER SUB-ASSEMBLY


D009943E02
  1. Remove the 11 bolts.



    D003584E01
  1. Tap in the circumference of the rear cover with a plastic-fased hammer to remove the transaxle rear cover from the transaxle.

  1. Remove the 2 oil seal rings from the transaxle rear cover.



    C083140E01
  1. Using a T30 ''torx'' socket wrench, remove the 2 screws and transaxle rear cover plate.



    D003801E01
  1. Using SST, remove the needle-roller bearing from the transaxle rear cover.

    SST
    09387-00041   (09387-01040, 09387-01010, 09387-01030)



47. REMOVE BRAKE APPLY TUBE


D025510E01
  1. Remove the bolt, clamp and 2 brake apply tubes.

  1. Remove the brake apply tube from the clamp.



48. REMOVE FRONT CLUTCH APPLY TUBE
  1. Remove the front clutch apply tube from the clamp.



49. REMOVE NO. 1 GOVERNOR APPLY GASKET


D003591E01
  1. Using a screwdriver, remove the 2 apply gaskets.



50. REMOVE DIRECT CLUTCH ASSEMBLY


D003586E01
  1. Remove the thrust bearing and direct clutch from the transaxle.



    D003802E01
  1. Remove the bearing race from the direct clutch.



51. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


D003587E01
  1. Remove the rear planetary sun gear from the transaxle.



    D003791E01
  1. Remove the thrust bearing from the rear planetary sun gear.



    D003908E01
  1. Remove the No. 1 thrust washer from the rear planetary sun gear.



52. REMOVE 1-WAY CLUTCH ASSEMBLY


D003588E02
  1. Remove the 1-way clutch and thrust bearing from the transaxle.



    D003909E02
  1. Remove the inner race from the 1-way clutch.



53. REMOVE 1-WAY CLUTCH OUTER SLEEVE


D003589E03


54. REMOVE 2ND BRAKE CLUTCH DISC


C129388
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 3 discs and 3 plates from the transaxle.



55. INSPECT 2ND BRAKE CLUTCH DISC


D004083E01
  1. Check to see if the sliding surface of the disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc is peeling off or discolored, or even if a part of the printed number is defaced, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.



56. REMOVE 2ND BRAKE PISTON ASSEMBLY


D008058E03
  1. Using a screwdriver, remove the snap ring.



    D008059E01
  1. Remove the 2nd brake piston from the transaxle.



57. REMOVE REAR PLANETARY GEAR ASSEMBLY


D003616E02
  1. Using a screwdriver, pry out the snap ring.



    D008062E01
  1. Remove the rear planetary gear from the transaxle.



    D003910E01
  1. Remove the No. 1 planetary carrier thrust washer from the rear planetary gear.



    D003593E01
  1. Remove the bearing race from the rear planetary gear.



58. REMOVE INPUT SUN GEAR


D003873E03
  1. Remove the 2 thrust bearings, bearing race and input sun gear from the transaxle.



59. REMOVE FRONT PLANETARY GEAR ASSEMBLY


D003595E02
  1. Using a chisel and hammer, unstake the lock washer.

    NOTICE:
    Push down all claws of the washer. Otherwise SST cannot be fully pressed against the nut and cannot loosen the nut.



    D003596E01
  1. Using SST, remove the nut.

    SST
    09387-00030  
    09387-00080  



    D003597E01
  1. Using SST and a press, remove the front planetary gear from the counter drive gear.

    SST
    09950-60010   (09951-00450)



    D008063E01
  1. Remove the front planetary gear from the brake hub.



60. REMOVE FRONT PLANETARY RING GEAR


D003615E03
  1. Using a screwdriver, remove the snap ring and front planetary ring gear from the brake hub.



61. REMOVE 1ST AND REVERSE BRAKE CLUTCH DISC


D009941E01
  1. Remove the flange, 5 discs and 5 plates from the transaxle case.



62. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC


D009189E01
  1. Check to see if the sliding surface of the disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc is peeling off or discolored, or even if a part of the groove is defaced, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.



63. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


D003600E01
  1. Using SST, a press and snap ring expander, remove the snap ring and piston return spring.

    SST
    09387-00070  

    NOTICE:
    1. Stop the press when the spring sheet is lowered 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove, preventing the spring sheet from deforming.
    2. Do not expand the snap ring excessively.



64. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


D003811E01
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.51 mm (0.6106 in.)



65. REMOVE 1ST AND REVERSE BRAKE PISTON


D003800E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.



    D003913E01
  1. Remove the 2 O-rings from the 1st and reverse brake piston.



66. REMOVE COUNTER DRIVE GEAR


D003601E01
  1. Using SST and a press, remove the counter drive gear from the transaxle case.

    SST
    09950-60010   (09951-00580)
    09950-70010   (09951-07100)



    D003602E01
  1. As shown in the illustration, tighten the 2 bolts evenly and make a clearance of approximately 20.0 mm (0.797 in.) between the counter drive gear and the inner race.



    D003603E02
  1. Using SST, remove the tapered roller bearing.

    SST
    09950-60010   (09951-00580)
    09950-00020  
    09950-00030  



    D003798E01
  1. Using a brass bar and hammer, tap out the 2 bearing outer races.



67. REMOVE COUNTER DRIVE GEAR HOLE SNAP RING


D003604E01
  1. Using a screwdriver, pry out the snap ring from the transaxle.



68. REMOVE NO. 2 BREATHER PLUG


69. REMOVE UNDERDRIVE BRAKE PISTON


D003799E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the underdrive brake piston.



    D003794E02
  1. Remove the 2 O-rings from the underdrive brake piston.



    D003605E02
  1. Using SST, remove the needle-roller bearing from the transaxle.

    SST
    09387-00041   (09387-01010, 09387-01030, 09387-01040)



70. REMOVE UNDERDRIVE CLUTCH DRUM OIL SEAL RING


D003914E04
  1. Remove the 2 oil seal rings from the transaxle.



71. REMOVE UNDERDRIVE CYLINDRICAL ROLLER BEARING


D003606E02
  1. Using SST, remove the cylindrical roller bearing from the transaxle.

    SST
    09514-35011  



72. REMOVE UNDERDRIVE OUTPUT SHAFT OIL SEAL RING


D003915E07
  1. Remove the oil seal ring from the transaxle housing.



73. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


D003607E01
  1. Remove the bolt, clamp and apply tube from the transaxle.