AUTOMATIC TRANSAXLE UNIT > REASSEMBLY |
| 1. BEARING POSITION |

| Mark | Front Race Diameter Inside / Outside | Thrust Bearing Diameter Inside / Outside | Rear Race Diameter Inside / Outside |
| A | - | 57.2 mm (2.252 in.) / 84.96 mm (3.3449 in.) | 56.4 mm (2.220 in.) / 83.0 mm (3.268 in.) |
| B | - | 37.73 mm (1.4854 in.) / 58.0 mm (2.283 in.) | 29.9 mm (1.177 in.) / 55.5 mm (2.185 in.) |
| C | - | 33.85 mm (1.3327 in.) / 52.2 mm (2.055 in.) | - |
| D | - | 23.5 mm (0.925 in.) / 44.0 mm (1.732 in.) | - |
| E | - | 36.3 mm (1.429 in. ) / 52.2 mm (2.055 in.) | 34.5 mm (1.358 in.) / 48.5 mm (1.909 in.) |
| F | - | 34.6 mm (1.362 in.) / 52.2 mm (2.055 in.) | - |
| G | 40.3 mm (1.587 in.) / 58.0 mm (2.283 in.) | 38.6 mm (1.520 in.) / 60.0 mm (2.362 in.) | 38.6 mm (1.520 in.) / 58.0 mm (2.283 in.) |
| H | - | 53.6 mm (2.110 in.) / 69.6 mm (2.740 in.) | - |
| I | - | 33.8 mm (1.331 in.) / 48.2 mm (1.898 in.) | 30.3 mm (1.193 in.) / 46.0 mm (1.811 in.) |
| J | - | 53.6 mm (2.110 in.) / 70.18 mm (2.763 in.) or 69.6 mm (2.740 in.) | - |
| 2. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE |
![]() |
Install the apply tube and clamp to the transaxle housing with the bolt.
| 3. INSTALL UNDERDRIVE OUTPUT SHAFT OIL SEAL RING |
![]() |
Install a new oil seal ring to the transaxle housing.
| 4. INSTALL UNDERDRIVE CYLINDRICAL ROLLER BEARING |
![]() |
Using SST and a press, press in the underdrive cylindrical roller bearing.
| 5. INSTALL UNDERDRIVE CLUTCH DRUM OIL SEAL RING |
![]() |
Install 2 new oil seal rings to the transaxle.
| 6. INSTALL UNDERDRIVE BRAKE PISTON |
![]() |
Wind a vinyl tape around SST at the place 4.0 mm (0.157 in.) above from the bottom end until the thickness of the wound tape is about 5.0 mm (0.197 in.)
![]() |
Using SST and a press, press in the needle-roller bearing to the transaxle until the wound vinyl tape contacts the transaxle case.
![]() |
Coat 2 new O-rings with ATF, and install them to the underdrive brake piston.
![]() |
Install the underdrive brake piston to the transaxle.
![]() |
Using SST, a snap ring expander and press, press in the piston return spring and snap ring to the transaxle.
| 7. INSTALL NO. 2 BREATHER PLUG |
| 8. INSTALL COUNTER DRIVE GEAR HOLE SNAP RING |
![]() |
Using a screwdriver, press in the snap ring to the transaxle.
| 9. INSTALL COUNTER DRIVE GEAR |
![]() |
Using SST and a press, press in the 2 bearings outer races to the transaxle.
![]() |
Using SST and a press, press in the tapered roller bearing to the counter drive gear until the bearing race contacts with the snap ring.
![]() |
Using SST and a press, install the counter drive gear and bearing to the transaxle.
| 10. INSTALL 1ST AND REVERSE BRAKE PISTON |
![]() |
Coat 2 new O-rings with ATF.
Install the 2 O-ring to the 1st and reverse brake piston.
![]() |
Coat the 1st and reverse brake piston with ATF, and install it to the transaxle.
| 11. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using SST, a press and snap ring expander, press the piston return spring and snap ring to the transaxle.
| 12. INSTALL FRONT PLANETARY RING GEAR |
![]() |
Using a screwdriver, install the front planetary ring gear and snap ring to the brake hub.
| 13. INSTALL FRONT PLANETARY GEAR ASSEMBLY |
![]() |
Install the front planetary gear assembly to the brake hub.
![]() |
Using SST and a press, press-fit the front planetary gear.
![]() |
Install the washer, as shown in the illustration.
![]() |
Using SST, install the nut.
![]() |
Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm. When the measured value is not within the specified value, gradually tighten the nut until it reaches the specified value.
![]() |
Using a chisel and hammer, stake the front planetary gear washer.
| 14. INSTALL INPUT SUN GEAR |
![]() |
Install the 2 thrust bearings, bearing race and front planetary sun gear to the front planetary gear.
| Item | Inside | Outside |
| Bearing | 34.6 mm (1.362 in.) | 52.2 mm (2.055 in.) |
| Race | 40.3 mm (1.587 in.) | 58.0 mm (2.283 in.) |
| Bearing | 38.6 mm (1.52 in.) | 60.0 mm (2.362 in.) |
| 15. INSTALL REAR PLANETARY GEAR ASSEMBLY |
![]() |
Coat the bearing race with ATF, and install it to the rear planetary gear assembly.
| Item | Inside | Outside |
| Race | 38.6 mm (1.520 in.) | 58.0 mm (2.83 in.) |
![]() |
Install the No. 2 thrust washer.
![]() |
Install the rear planetary gear to the rear planetary ring gear.
![]() |
Using a screwdriver, install the snap ring.
| 16. INSTALL 1ST AND REVERSE BRAKE CLUTCH DISC |
![]() |
Install the 5 plates and 5 discs.
![]() |
Using a vernier caliper, measure the distance between the disc surface and the contact surface of the 2nd brake cylinder and transaxle (Dimension A).
Select an appropriate flange so that the pack clearance will meet the specified value.
0.745 to 1.21 mm (0.0293 to 0.0476 in.)
| Mark | Thickness | Mark | Thickness |
| 1 | 1.8 mm (0.071in.) | 5 | 2.2 mm (0.087 in.) |
| 2 | 1.9 mm (0.075 in.) | 6 | 2.3 mm (0.091 in.) |
| 3 | 2.0 mm (0.079 in.) | 7 | 2.4 mm (0.094 in.) |
| 4 | 2.1 mm (0.083 in.) | 8 | 2.5 mm (0.098 in.) |
![]() |
Install the flange.
| 17. INSTALL 2ND BRAKE PISTON ASSEMBLY |
![]() |
Install the 2nd brake piston to the transaxle.
Install the snap ring and measure the inside diameter.
| 18. INSTALL 1-WAY CLUTCH SLEEVE OUTER |
![]() |
Install the 1-way clutch outer sleeve to the 2nd brake cylinder.
| 19. INSTALL 1-WAY CLUTCH ASSEMBLY |
![]() |
Install the inner race to the 1-way clutch.
![]() |
Check the rotating direction of the 1-way clutch for the lock or free operation, as shown in illustration.
![]() |
Install the 1-way clutch and bearing to the 1-way clutch sleeve outer.
| Item | Inside | Outside |
| Bearing | 53.6 mm (2.110 in.) | 69.6 mm (2.740 in.) |
| 20. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY |
![]() |
Coat the No. 1 thrust washer with petroleum jelly, and install it onto the rear planetary sun gear.
![]() |
Coat the bearing with petroleum jelly, and install it onto the rear planetary sun gear.
| Item | Inside | Outside |
| Bearing | 33.8 mm (1.331 in) | 48.2 mm (1.898 in.) |
![]() |
Install the rear planetary sun gear to the rear planetary gear.
| 21. INSTALL 2ND BRAKE CLUTCH DISC |
![]() |
Install the 3 discs and 3 plates to the transaxle.
Temporarily install the snap ring.
![]() |
Using a vernier caliper, measure the distance between the disc surface and snap ring surface.
Select an appropriate flange so that the pack clearance will meet the specified value.
| Mark | Thickness | Mark | Thickness |
| 1 | 3.0 mm (0.118 in.) | 5 | 3.4 mm (0.134 in.) |
| 2 | 3.1 mm (0.122 in.) | 6 | 3.5 mm (0.138 in.) |
| 3 | 3.2 mm (0.126 in.) | 7 | 3.6 mm (0.142 in.) |
| 4 | 3.3 mm (0.130 in) | 8 | - |
![]() |
Temporarily remove the snap ring, attach the selected flange and restore the snap ring.
| 22. INSTALL DIRECT CLUTCH |
![]() |
Install the bearing race to the direct clutch.
| Item | Inside | Outside |
| Bearing race | 30.3 mm (1.193 in.) | 46.0 mm (1.811 in.) |
![]() |
Install the direct clutch and thrust bearing to the rear planetary sun gear.
![]() |
Clean the connector part of the transaxle case and rear cover.
As shown in the illustration, place a straightedge on the direct clutch drum and measure the distance between the transaxle case and the straightedge using a vernier caliper (Dimension B).
![]() |
Measure the 2 places of the rear cover as shown in the illustration. Calculate a dimension C using the following formula.
Calculate the end play value using the following formula. Select a thrust bearing which satisfies the end play value and install it.
| Thickness | Inside | Outside |
| 3.58 mm (0.1409 in.) | 53.6 mm (2.110 in.) | 69.6 mm (2.740 in.) |
| 3.88 mm (0.1528 in.) | 53.6 mm (2.110 in.) | 70.18 mm (2.768 in.) |
| 23. INSTALL NO. 1 GOVERNOR APPLY GASKET |
![]() |
Install 2 new governor apply gaskets.
| 24. INSTALL FRONT CLUTCH APPLY TUBE |
![]() |
Install the clamp to the front clutch apply tube.
| 25. INSTALL BRAKE APPLY TUBE |
![]() |
Install the clamp to the brake apply tube.
![]() |
Install the 2 apply tubes and to the transaxle with the bolt.
| 26. INSTALL NO. 1 TRANSAXLE CASE PLUG |
![]() |
Install 2 new O-rings to the 2 plugs.
Install the 2 plugs to the transaxle rear cover.
| 27. INSTALL TRANSAXLE REAR COVER SUB-ASSEMBLY |
![]() |
Using SST and a press, press in the bearing.
Apply adhesive to the 2 screws.
![]() |
Using a T30 ''torx'' socket wrench, install the transaxle rear cover plate with the 2 screws.
![]() |
Coat 2 new oil seal rings with ATF, and install them to the transaxle rear cover.
![]() |
Remove any packing material and be careful not to get oil on the contacting surfaces of the transaxle rear cover or the transaxle.
Apply FIPG to the cover.
Coat the needle roller bearing with ATF.
![]() |
Apply adhesive to the threads of the bolts labeled A.
Install the 11 bolts.
| 28. INSTALL NO. 2 UNDERDRIVE CLUTCH DISC |
![]() |
Install the 3 discs and 3 plates to the transaxle.
Using a screwdriver, install the snap ring.
![]() |
Using a dial indicator, measure the underdrive brake pack clearance while applying and releasing compressed air (392kPa, 4.0 kgf/cm2, 57 psi).
| Mark | Thickness | Mark | Thickness |
| 1 | 3.0 mm (0.118 in.) | 3 | 3.4 mm (0.134 in.) |
| 2 | 3.2 (0.126 in.) | - | - |
Temporarily remove the snap ring and attach the flange. Restore the snap ring.
| 29. INSPECT UNDERDRIVE 1-WAY CLUTCH ASSEMBLY |
![]() |
Install the underdrive clutch assembly to the 1-way clutch. Rotate the underdrive clutch assembly to check the rotating direction for the lock or free operation.
| 30. INSTALL UNDERDRIVE 1 WAY CLUTCH ASSEMBLY |
![]() |
Install the outer race retainer to the 1-way clutch.
![]() |
Install the 1-way clutch to the transaxle.
![]() |
Using a screwdriver, install the snap ring to the transaxle.
| 31. INSTALL UNDERDRIVE CLUTCH ASSEMBLY |
![]() |
Coat the bearing and bearing race with petroleum jelly, and install them onto the underdrive clutch.
| Item | Inside | Outside |
| Bearing | 37.73 mm (1.4854 in.) | 58.0 mm (2.283 in.) |
| Race | 29.9 mm (1.177 in.) | 55.5 mm (2.185 in.) |
Install the underdrive clutch to the transaxle.
| 32. INSTALL UNDERDRIVE PLANETARY GEAR |
![]() |
Install the pawl pin and spring to the parking lock pawl.
![]() |
Temporarily install the parking lock pawl, shaft and spring to the transaxle case as shown in the illustration.
![]() |
Install the underdrive planetary gear to the transaxle.
![]() |
Install the parking lock pawl shaft.
![]() |
Install the pawl shaft clamp with the bolt.
![]() |
Using a straightedge and vernier calipers as shown in the illustration, measure the gap between the top of the differential drive pinion in the underdrive planetary gear and contact surface of the transaxle and housing (Dimension D).
![]() |
As shown in the illustration, measure the 2 places of the transaxle housing. Calculate the dimension E using the formula.
| 33. INSTALL MULTIPLE DISC CLUTCH HUB |
![]() |
Install the bearing race to the transaxle while checking its direction.
| Item | Inside | Outside |
| Bearing race | 34.5 mm (1.358 in.) | 48.5 mm (1.909 in.) |
![]() |
Coat the thrust bearing and race with petroleum jelly, and install them onto the multiple disc clutch hub.
| Item | Inside | Outside |
| Bearing | 36.3 mm (1.429 in.) | 52.2 mm (2.055 in.) |
![]() |
Install the bearing to the multiple clutch hub.
| Item | Inside | Outside |
| Bearing | 23.5 mm (0.925 in.) | 44.0 mm (1.732 in.) |
Install the forward clutch hub to the transaxle.
| 34. INSTALL FORWARD CLUTCH ASSEMBLY |
![]() |
Install the thrust bearing to the forward clutch.
| Item | Inside | Outside |
| Bearing | 33.85 mm (1.3327 in.) | 52.2 mm (2.055 in.) |
![]() |
Install the forward clutch to the multiple clutch hub.
| 35. INSTALL OVERDRIVE BRAKE GASKET |
![]() |
Install 2 new overdrive brake gaskets.
| 36. INSTALL DIFFERENTIAL GEAR ASSEMBLY |
![]() |
Install the differential gear to the transaxle.
| 37. INSTALL NO. 2 THRUST BEARING UNDERDRIVE RACE |
![]() |
Install the thrust bearing race to the underdrive planetary gear.
| 38. INSTALL THRUST NEEDLE ROLLER BEARING |
![]() |
Calculate the end play value using the following formula and values of Dimensions D and E that were measured when installing cylindrical roller bearing and underdrive planetary gear. Select an appropriate underdrive planetary gear thrust bearing race No. 2 which satisfies the specified end play value, and instal it.
| E - D | Thickness |
| Less than 7.64 mm (0.3008 in.) | 3.5 mm (0.138 in.) |
| 7.64 mm (0.3008 in.) | 3.8 m (0.150 in.) |
| Item | Inside | Outside |
| Bearing | 57.2 mm (2.252 in.) | 84.96 mm (3.3449 in.) |
| Bearing race | 56.4 mm (2.220 in.) | 83.0mm (3.268 in.) |
| 39. INSTALL OIL PUMP ASSEMBLY |
![]() |
Install the oil pump to the transaxle with the 7 bolts.
![]() |
Coat the O-ring of the oil pump with ATF.
| 40. INSTALL TRANSAXLE HOUSING |
![]() |
Remove any packing material and be careful not to get oil on the contacting surface of the transaxle housing.
Apply FIPG to the transaxle.
![]() |
Install the transaxle housing to the transaxle with the 16 bolts.
| 41. INSTALL NO. 1 TRANSAXLE CASE PLUG |
![]() |
Install 2 new O-rings to the 2 plugs.
Install the 2 plugs to the transaxle housing.
| 42. INSPECT INPUT SHAFT END PLAY |
![]() |
Using a dial indicator, measure the input shaft end play.
| 43. FIX AUTOMATIC TRANSAXLE ASSEMBLY |
![]() |
| 44. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL |
![]() |
Coat a new oil seal with ATF.
Install the oil seal to the transaxle.
| 45. INSTALL PARKING LOCK ROD SUB-ASSEMBLY |
![]() |
Install the parking lock rod to the manual valve lever.
| 46. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY |
![]() |
Install a new spacer and manual valve lever shaft to the transaxle.
![]() |
Using a pin punch and hammer, tap in a new pin.
![]() |
Turn the spacer and lever shaft to align the small hole for locating the staking position mark on the lever shaft.
Using a pin punch, stake the spacer through the small hole.
Check that the spacer does not turn.
| 47. INSTALL MANUAL VALVE LEVER SHAFT RETAINER SPRING |
![]() |
Using needle-nose pliers, install the retainer spring.
| 48. INSTALL PARKING LOCK PAWL BRACKET |
![]() |
Install the parking lock pawl bracket with the 2 bolts.
| 49. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY |
![]() |
Install the manual detent spring with the 2 bolts.
| 50. INSTALL B-3 ACCUMULATOR PISTON |
![]() |
Coat a new O-ring with ATF, and install it to the B-3 accumulator piston.
![]() |
Coat the piston with ATF, install it to the transaxle.
| Spring | Free length Outer diameter | Color |
| B-3 Inner | 60.24 mm (2.3716 in.) 15.9 (0.626 in.) | Yellowish green |
| B-3 Outer | 74.61 mm (2.9374 in.) 21.7 mm (0.854 in.) | Blue |
| 51. INSTALL C-1 ACCUMULATOR PISTON |
![]() |
Coat 2 new O-rings with ATF, and install them to the C-1 accumulator piston.
![]() |
Coat the piston with ATF, and install it to the transaxle.
| Spring | Free length Outer diameter | Color |
| C-1 | 81.53 mm (3.2098 in.) 18.5 mm (0.728 in.) | Pink |
| 52. INSTALL C-3 ACCUMULATOR PISTON |
![]() |
Coat a new O-ring with ATF, and install it to the C-3 accumulator piston.
![]() |
Coat the piston with ATF, install it to the transaxle case.
| Spring | Free length Outer diameter | Color |
| C - 3 | 90.49 mm (3.5626 in.) 19.2 mm (0.756 in.) | White |
![]() |
Install the spring from the C-3 accumulator piston.
| 53. INSTALL CHECK BALL BODY |
![]() |
Install the check ball body and spring.
| 54. INSTALL BRAKE DRUM GASKET |
![]() |
Coat a new brake drum gasket with ATF, and install it to the transaxle.
| 55. INSTALL TRANSAXLE CASE 2ND BRAKE GASKET |
![]() |
Coat a new transaxle case 2nd brake gasket with ATF, and install it to the transaxle.
| 56. INSTALL NO. 1 GOVERNOR APPLY GASKET |
![]() |
Coat a new governor apply gasket No. 1 with ATF, and install it to the transaxle.
| 57. INSTALL TRANSMISSION WIRE |
![]() |
Coat a new O-ring with ATF, and install it to the transaxle solenoid wire.
![]() |
Install the solenoid wire retaining bolt
| 58. INSTALL TRANSMISSION VALVE BODY ASSEMBLY |
![]() |
Align the groove of the manual valve with the pin of lever.
Install the 17 bolts.
![]() |
Connect the 5 solenoid connectors.
Coat the O-ring of the temperature sensor with ATF.
Install the ATF temperature sensor with the lock plate and bolt.
| 59. INSTALL VALVE BODY OIL STRAINER ASSEMBLY |
![]() |
Coat a new O-ring with ATF.
Install the O-ring to the oil strainer.
![]() |
Install the oil strainer with the 3 bolts.
| 60. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY |
![]() |
Install the 3 magnets in the oil pan.
Install a new oil pan gasket to the oil pan.
![]() |
Install the oil pan to the transaxle with the 18 bolts.
| 61. INSTALL NO. 1 TRANSAXLE CASE PLUG |
![]() |
Coat 4 new O-rings with ATF, and install them to the 4 plugs.
Install the 4 plugs to the transaxle case.
| 62. INSTALL SPEED SENSOR |
![]() |
Coat 2 new O-rings with ATF, and install them to the 2 sensors.
Install the 2 sensors with the 2 bolts.
| 63. INSTALL OIL COOLER INLET TUBE UNION |
![]() |
Coat a new O-ring with ATF, and install it to the union.
Install the union to the transaxle.
| 64. INSTALL OIL COOLER OUTLET TUBE UNION |
![]() |
Coat a new O-ring with ATF, and install it to the union.
Install the union to the transaxle.
| 65. INSTALL BREATHER PLUG HOSE |
| 66. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Install the park/neutral position switch to the manual valve shaft.
Temporarily install the 2 bolts.
Install a new lock plate and tighten the manual valve shaft nut.
![]() |
Temporarily install the control shaft lever.
![]() |
Turn the lever counterclockwise until it stops, and then turn it clockwise 2 notches.
Remove the control shaft lever.
![]() |
Align the groove with neutral basic line.
Hold the switch in this position and tighten the 2 bolts.
![]() |
Using a screwdriver, stake the nut with the lock plate.
![]() |
Install the control shaft lever with the washer and nut.