DIFFERENTIAL CASE > REASSEMBLY |
| 1. INSTALL FRONT DIFFERENTIAL SIDE GEAR |
![]() |
Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF and install them to the differential case.
| 2. INSTALL NO. 1 FRONT DIFFERENTIAL PINION SHAFT |
![]() |
Coat the No. 1 front differential pinion shaft with ATF, and install it to the differential case.
| 3. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN |
![]() |
Using a pin punch and a hammer, tap in the pinion shaft straight pin.
![]() |
Using a chisel and a hammer, stake the differential case.
| 4. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
![]() |
Using SST and a press, press in the front differential case rear tapered roller bearing to the differential case.
![]() |
Using SST and a hammer, tap in the front differential case rear tapered roller bearing outer race to the transaxle housing.
| 5. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a press, press in the front differential case front tapered roller bearing to the differential case.
![]() |
Using SST and a hammer, tap in the front differential case front tapered roller bearing outer race to the transaxle housing.
| 6. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD |
![]() |
Install the differential assembly to the transaxle case.
![]() |
Clean the matching surfaces of the transaxle case and transaxle housing.
Install the transaxle housing to the transaxle case and tighten them with the 16 bolts.
![]() |
Using SST, turn the differential assembly right and left 2 or 3 times to allow the bearing to settle.
Using SST and a torque wrench, measure the turning torque of the differential.
| Mark | Thickness | Mark | Thickness |
| 0 | 2.00 mm (0.0787 in.) | J | 2.025 mm (0.07972 in.) |
| 1 | 2.05 mm (0.0807 in.) | K | 2.075 mm (0.08169 in.) |
| 2 | 2.10 mm (0.0827 in.) | L | 2.125 mm (0.08366 in.) |
| 3 | 2.15 mm (0.0846 in.) | M | 2.175 mm (0.08563 in.) |
| 4 | 2.20 mm (0.0866 in.) | N | 2.225 mm (0.08760 in.) |
| 5 | 2.25 mm (0.0886 in.) | P | 2.275 mm (0.08957 in.) |
| 6 | 2.30 mm (0.0906 in.) | Q | 2.325 mm (0.09154 in.) |
| 7 | 2.35 mm (0.0925 in.) | R | 2.375 mm (0.09350 in.) |
| 8 | 2.40 mm (0.0945 in.) | S | 2.425 mm (0.09547 in.) |
| 9 | 2.45 mm (0.0965 in.) | T | 2.475 mm (0.09744 in.) |
| A | 2.50 mm (0.0984 in.) | U | 2.525 mm (0.09941 in.) |
| B | 2.55 mm (0.1004 in.) | V | 2.575 mm (0.10138 in.) |
| C | 2.60 mm (0.1024 in.) | W | 2.625 mm (0.10335 in.) |
| D | 2.65 mm (1.1043 in.) | X | 2.675 mm (0.10531 in.) |
| E | 2.70 mm (0.1063 in.) | Y | 2.725 mm (0.10728 in.) |
| F | 2.75 mm (0.1083 in.) | AA | 2.775 mm (0.10925 in.) |
| G | 2.80 mm (0.1102 in.) | AB | 2.825 mm (0.11122 in.) |
| H | 2.85 mm (0.1122 in.) | - | - |
![]() |
Remove the 16 bolts and the transaxle housing.
![]() |
Remove the differential assembly.
| 7. INSTALL FRONT DIFFERENTIAL RING GEAR |
![]() |
Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).
Clean the contract surface of the front differential case.
![]() |
Align the matchmarks, and install the front differential ring gear case quickly.
![]() |
Tighten the 14 bolts.
| 8. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL |
![]() |
Coat the lip of a new oil seal with a small amount of MP grease.
Using SST and a hammer, tap in the oil seal.
| 9. INSTALL TRANSAXLE HOUSING OIL SEAL |
![]() |
Wrap vinyl tape around SST at the place 6.0 mm (0.236 in.) above the bottom end until the thickness of the wrapped tape is approximately 5.0 mm (0.197 in.).
![]() |
Coat the lip of a new oil seal with a small amount of MP grease.
Using SST and a hammer, tap in the oil seal.