ELECTRONIC POWER STEERING SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Read the Data List by following the directions on the tester screen.
| Tester Display | Measurement Item/Range | Normal Condition | Reference Value |
| Meter Vehicle Velocity | Vehicle speed from meter: Min.: 0 km/h (0 mph) Max.: 300 km/h (187.5 mph) | Vehicle stopped | 0 km/h (0 mph) |
| Vehicle driven at constant speed | No significant fluctuation | ||
| Engine Revolution | Show the engine revolution: Min.: 0 rpm Max.: 12800 rpm | Engine is running at a constant speed | No significant fluctuation |
| Motor Actual Current | Amount of current to motor: Min.: -327.68 A Max.: 327.67 A | Power steering is in operation | Value changes in proportion to steering effort |
| Command Value Current | Demanded amount of current to motor: Min.: -327.68 A Max.: 327.67 A | Power steering is in operation | Value changes in proportion to steering effort |
| Steering Angle Velocity | Steering angle speed: Min.: -32768 deg/s Max.: 32767 deg/s | Steering wheel is turned | Value changes in proportion to steering effort |
| Thermistor Temperature | ECU substrate temperature: Min.: -40°C Max.: 150°C | Ignition switch on (IG) | - |
| PIG Power Supply | Power source voltage to activate motor: Min.: 0 V Max.: 20.1531 V | Power steering in operation | 10 to 14 V |
| IG Power Supply | ECU power source voltage: Min.: 0 V Max.: 20.1531 V | Ignition switch on (IG) | 10 to 14 V |
| Steering Wheel Torque | Steering wheel torque: Min.: -327.68 Nm Max.: 7 Nm | - | - |
| Motor Rotation Angle | Motor rotation angle: Min.: 0 deg Max.: 1441.77 deg | Power steering in operation | During steering operation, motor rotation angle value changes from 0 to 360° |
| Motor Voltage | Motor power supply voltage: Min.: 0 V Max.: 98 V | Power steering in operation | - |
| Motor Terminal Volt (U) | Motor terminal voltage (U phase): Min.: 0 V Max.: 98 V | Engine running and steering wheel turned | When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed. |
| Motor Terminal Volt (V) | Motor terminal voltage (V phase): Min.: 0 V Max.: 98 V | Engine running and steering wheel turned | When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed. |
| Motor Terminal Volt (W) | Motor Terminal voltage (W phase): Min.: 0 V Max.: 98 V | Engine running and steering wheel turned | When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed. |
| Torque Sensor 1 Output | Torque sensor 1 output voltage/ Min.: 0 V Max.: 5 V | 2.3 to 2.7 V | Steering wheel is not turned (without load) |
| 2.5 to 4.04 V | Steering wheel is turned to the right when the vehicle is stopped | ||
| 0.95 to 2.5 V | Steering wheel is turned to the left when the vehicle is stopped | ||
| Torque Sensor 2 Output | Torque sensor 2 output voltage/ Min.: 0 V Max.: 5 V | 2.3 to 2.7 V | Steering wheel is not turned (without load) |
| 0.95 to 2.5 V | Steering wheel is turned to the right when the vehicle is stopped | ||
| 2.5 to 4.04 V | Steering wheel is turned to the left when the vehicle is stopped | ||
| IG ON/OFF Times | Ignition switch ON/OFF number of times after fail detection: Min.: 0 times Max.: 65535 times | - | - |
| Motor Overheat Record | Continuous overheat prevention control record: Rec or Unrec | Unrec | - |
| Motor Lo Power Record | PIG power source voltage drop record: Rec or Unrec | Unrec | - |
| Eng Rev Inter Record | Record of engine revolution signal interruption: Rec or Unrec | Unrec | - |
| Spd Sig Invalid Record | Record of vehicle speed signal invalid: Rec or Unrec | Unrec | - |
| Battery Voltage Lo Record | Number of battery voltage low: Min.: 0 times Max.: 65535 times | - | - |
| Battery Voltage | Battery voltage: Min.: 0 V Max.: 25.5 V | - | 10 to 14 V |
| PS Assist Signal | Power steering assist signal: ON or OFF | - | - |
| The Number of DTCs | Number of detected DTCs when freeze frame data stored: Min.: 0 Max.: 255 | - | - |
| PERFORM ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester ON.
Perform the Active Test by following the prompts on the tester.
| Tester Display | Test Part | Control Range |
| Indicat. EPS | P/S indicator ON/OFF | Confirm that vehicle is stopped, engine idling |