STEERING LOCK SYSTEM > Unable to Unlock Steering Wheel |

| 1.CHECK ENGINE SWITCH ON (IG) |
except M/T:
Check whether the engine switch can be turned on (IG) when the shift position is on P and the brake pedal is depressed.
for M/T:
Check whether the engine switch can be turned on (IG) when the clutch pedal is depressed.
|
| ||||
| OK | |
| 2.CHECK DTC (MAIN BODY ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Check the DTCs of the main body ECU by following the prompts displayed on the intelligent tester.
|
| ||||
| OK | |
| 3.CHECK DTC (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Check the DTCs of the certification ECU by following the prompts displayed on the intelligent tester.
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Within 10 seconds of the engine switch being turned on, check the Data List and read the value displayed on the intelligent tester.
| Item | Measurement Item / Range | Normal Condition | Diagnostic Note |
| Lock / Unlock Receive | Steering lock command reception record / YES or NO | YES: Steering lock / unlock signal received NO: Steering lock / unlock signal not received | - |
|
| ||||
| OK | |
| 5.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - BODY GROUND) |
![]() |
Disconnect the E6 steering lock actuator connector.
Measure the voltage and resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E6-7 (B) - E6-1 (GND) | 11 to 14 V |
| E6-7 (B) - E6-2 (SGND) | 11 to 14 V |
| Tester Connection | Specified Condition |
| E6-1 (GND) - Body ground | Below 1 Ω |
| E6-2 (SGND) - Body ground | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK STEERING LOCK ACTUATOR |
![]() |
Immediately after turning the engine switch on (IG), inspect the voltage between terminals E6-3 (IGE) and E6-2 (SGND) of the steering lock actuator.
| Result | Proceed to |
| Immediately after turning engine switch on (IG), condition that measurement is 1 V or less occurs | A |
| Measurement is 11 to 14 V, and measurement never becomes 1 V or less | B |
|
| ||||
| A | ||
| ||
| 7.READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Check the Data List and read the value displayed on the intelligent tester.
| Item | Measurement Item / Range | Normal Condition | Diagnostic Note |
| S Code Check | S code match record / NG or OK | NG: S code not matched OK: S code matched | - |
|
| ||||
| NG | |
| 8.CHECK OPERATION OF ID CODE BOX |
Replace the ID code box with a normally functioning or new one.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Check the Data List and read the value displayed on the intelligent tester.
| Item | Measurement Item / Range | Normal Condition | Diagnostic Note |
| S Code Check | S code match record / NG or OK | NG: S code not matched OK: S code matched | - |
|
| ||||
| NG | ||
| ||
| 9.READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Check the Data List and read the value displayed on the intelligent tester.
| Item | Measurement Item / Range | Normal Condition | Diagnostic Note |
| L Code Check | L code match record / NG or OK | NG: L code not matched OK: L code matched | - |
|
| ||||
| NG | |
| 10.CHECK OPERATION OF ID CODE BOX |
Replace the ID code box with a normally functioning or new one.
Connect the intelligent tester to theDLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Check the Data List and read the value displayed on the intelligent tester.
| Item | Measurement Item / Range | Normal Condition | Diagnostic Note |
| L Code Check | L code match record / NG or OK | NG: L code not matched OK: L code matched | - |
|
| ||||
| NG | ||
| ||
| 11.CHECK OPERATION OF STEERING LOCK ACTUATOR |
Replace the steering lock actuator assembly with a normally functioning or new one.
except M/T:
With the shift lever on P and the brake pedal depressed, turn the engine switch on (IG).
for M/T:
With the clutch pedal depressed, turn the engine switch on (IG).
Check whether the steering lock can be released by turning the steering wheel, and check that the engine starts.
|
| ||||
| NG | ||
| ||