STEERING LOCK SYSTEM > Unable to Lock Steering Wheel |

| 1.CHECK DTC (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Read the DTCs of the certification ECU by following the prompts displayed on the intelligent tester.
|
| ||||
| OK | |
| 2.CHECK DTC (MAIN BODY ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Read the DTCs of the main body ECU by following the prompts displayed on the intelligent tester.
|
| ||||
| OK | |
| 3.READ VALUE USING DATA LIST (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Within 10 seconds after the engine is started, read the Data List menu of the certification ECU, and check the steering lock command reception record.
| Item | Measurement Item / Range | Normal Condition | Diagnostic Note |
| Lock / Unlock Receive | Steering lock command reception record / YES or NO | YES: Steering lock / unlock signal received NO: Steering lock / unlock signal not received | - |
|
| ||||
| OK | |
| 4.CHECK STEERING LOCK ACTUATOR |
![]() |
Turn the engine switch on (IG).
Turn the engine switch off.
With the shift lever on P*, immediately after opening the driver door, inspect the voltage between terminals E6-3 (IGE) and E6-2 (SGND) of the steering lock actuator.
*: except M/T
| Result | Proceed to |
| Immediately after opening door, condition that measurement is 1 V or less occurs | A |
| Measurement is 11 to 14 V, and measurement never becomes 1 V or less | B |
|
| ||||
| A | ||
| ||
| 5.CHECK STEERING LOCK FUNCTION |
Open the front passenger side door.
Lock the doors using the wireless remote door lock key.
Check that no doors are locked and the steering lock does not operate.
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Check the Data List and read the value displayed on the intelligent tester.
| Item | Measurement Item / Range | Normal Condition | Diagnostic Note |
| S Code Check | S code match record / NG or OK | NG: S code not matched OK: S code matched | - |
|
| ||||
| NG | |
| 7.CHECK OPERATION OF ID CODE BOX |
Replace the ID code box with a normally functioning or new one.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Check the Data List and read the value displayed on the intelligent tester.
| Item | Measurement Item / Range | Normal Condition | Diagnostic Note |
| S Code Check | S code match record / NG or OK | NG: S code not matched OK: S code matched | - |
|
| ||||
| NG | ||
| ||
| 8.READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Check the Data List and read the value displayed on the intelligent tester.
| Item | Measurement Item / Range | Normal Condition | Diagnostic Note |
| L Code Check | L code match record / NG or OK | NG: L code not matched OK: L code matched | - |
|
| ||||
| NG | |
| 9.CHECK OPERATION OF ID CODE BOX |
Replace the ID code box with a normally functioning or new one.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and press the intelligent tester main switch ON.
Check the Data List and read the value displayed on the intelligent tester.
| Item | Measurement Item / Range | Normal Condition | Diagnostic Note |
| L Code Check | L code match record / NG or OK | NG: L code not matched OK: L code matched | - |
|
| ||||
| NG | ||
| ||
| 10.CHECK OPERATION OF STEERING LOCK ACTUATOR |
Replace the steering lock actuator assembly with a normally functioning or new one.
except M/T:
With the shift lever on P and the brake pedal depressed, turn the engine switch on (IG).
for M/T:
With the clutch pedal depressed, turn the engine switch on (IG).
Check whether the steering lock can be released by turning the steering wheel, and check that the engine starts.
|
| ||||
| NG | ||
| ||