Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for DVD)

NAVIGATION SYSTEM (for DVD) > Speaker Circuit

for Preparation Click here


DESCRIPTION

A sound signal is sent from the navigation receiver assembly to the speakers through this circuit.

WIRING DIAGRAM


E173504E03


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check that the speakers sound.
    Result 
    Result
    Proceed to
    Front No. 1 speakers do not operate
    A
    Front No. 2 speakers do not operate
    B
    Rear No. 1 speakers do not operate
    C
    All speakers do not operate
    D



B
Go to step 4

C
Go to step 6

D
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


2.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E160614E19
  1. Disconnect the H6*1 and/or G7*2 speaker connector.

    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    1 (-) - 2 (TWL-)
    Always
    Below 1 Ω
    3 (+) - 4 (TWL+)
    Always
    Below 1 Ω
    for RH:
    Tester Connection
    Condition
    Specified Condition
    1 (-) - 2 (TWR-)
    Always
    Below 1 Ω
    3 (+) - 4 (TWR+)
    Always
    Below 1 Ω



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER - FRONT NO. 2 SPEAKER)
  1. *1: for LH
  2. *2: for RH


    E182174E01
  1. Disconnect the H1*1 and/or G1*2 speaker connector.



    E179044E05
  1. Disconnect the H6*1 and/or G7*2 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    H1-1 - H6-3 (+)
    Always
    Below 1 Ω
    H1-1 - Body ground
    Always
    10 kΩ or higher
    H1-2 - H6-1 (-)
    Always
    Below 1 Ω
    H1-2 - Body ground
    Always
    10 kΩ or higher
    for RH:
    Tester Connection
    Condition
    Specified Condition
    G1-1 - G7-3 (+)
    Always
    Below 1 Ω
    G1-1 - Body ground
    Always
    10 kΩ or higher
    G1-2 - G7-1 (-)
    Always
    Below 1 Ω
    G1-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - FRONT NO. 2 SPEAKER)


    E179012E05
  1. Disconnect the E52 navigation receiver assembly connector.



    E179044E06
  1. Disconnect the H6*1 and/or G7*2 speaker connector.

    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    E52-2 (FL+) - H6-4 (TWL+)
    Always
    Below 1 Ω
    E52-6 (FL-) - H6-2 (TWL-)
    Always
    Below 1 Ω
    E52-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    E52-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    for RH:
    Tester Connection
    Condition
    Specified Condition
    E52-1 (FR+) - G7-4 (TWR+)
    Always
    Below 1 Ω
    E52-5 (FR-) - G7-2 (TWR-)
    Always
    Below 1 Ω
    E52-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    E52-5 (FR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Temporarily replace the speaker with a new or normally functioning one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all speaker connectors to the speakers.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.

    Result 
    Result
    Proceed to
    Malfunction does not disappear
    A
    Malfunction disappears
    B



B
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - REAR NO. 1 SPEAKER)


    E179040E03
  1. Disconnect the E53 navigation receiver assembly connector.



    E182174E02
  1. Disconnect the J2*1 and/or I2*2 speaker connector.

    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    E53-2 (RL+) - J2-1
    Always
    Below 1 Ω
    E53-6 (RL-) - J2-2
    Always
    Below 1 Ω
    E53-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    E53-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    for RH:
    Tester Connection
    Condition
    Specified Condition
    E53-1 (RR+) - I2-1
    Always
    Below 1 Ω
    E53-3 (RR-) - I2-2
    Always
    Below 1 Ω
    E53-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    E53-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    E144966E30
  1. Disconnect the J2*1 and/or I2*2 speaker connector.

    1. *1: for LH
    2. *2: for RH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)