ENTRY AND START SYSTEM > SYSTEM DESCRIPTION |
| ENTRY AND START SYSTEM |
In addition to conventional mechanical key and wireless door lock control functions, the entry and start system enables door locking/unlocking, steering lock releasing, engine starting and back door opening without operating the key. The only requirement is that the key is in the user's possession.
| DETECTION AREA |

Precautions for the entire system:
| FUNCTION OF MAIN COMPONENTS |
| Components | Function |
| Key |
|
| Certification ECU | Controls entry and start system in accordance with signals from each oscillator, various switches, ECUs and key
|
| Main body ECU | Controls push button start function in accordance with signals from various switches, ECUs and combination meter
|
| ID code box |
|
| Outside door handle (driver, passenger and back doors) (antenna) | Transmits request signals |
| Outside door handle (driver, passenger and back doors) (touch sensor) | Detects when person touches inside of outside handle |
| Outside door handle (driver, passenger and back doors) (lock switch) | Transmits door lock request signals to certification ECU |
| Door electrical key oscillator (driver, passenger and back doors) | Receives request signal from certification ECU, and forms detection area around each door |
| Indoor electrical key oscillator (for front and for rear) | Receives request signal from certification ECU, and forms detection area in vehicle interior |
| Back door oscillator | Receives the request signal from the certification ECU, and forms the actuation area around the back door |
| Door control receiver | Receives the ID code from the key in the actuation area and transmits it to the certification ECU |
| Back door open switch | Transmits a back door open request signal to the main body ECU |
| Back door lock switch | Transmits a back door lock request signal to the certification ECU |
| Clutch start switch*1 | Outputs state of clutch start switch to main body ECU |
| Stop light switch*2 | Outputs state of clutch brake pedal to main body ECU |
| Wireless door lock buzzer | When certification ECU detects human errors such as those below, it warns driver by sounding wireless door lock buzzer and sounds the buzzer in accordance with request signal from ECU Example:
|
Combination meter
|
| CONSTRUCTION AND OPERATION |
Key:
The key consists of a mechanical key, transmitter for the wireless door lock remote control, transceiver for the entry and start system, and transponder chip for the engine immobiliser control.

Oscillator (front LH and RH door oscillators, front and rear indoor oscillators, back door oscillator):
Each oscillator transmits the request signal received from the certification ECU, and forms a key detection area to detect the presence of a key. The detection area formed by each door electrical key oscillator and back door electrical key oscillator is approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) from the outside handle of the front LH and RH doors or from the center of the rear bumper.
| ENTRY FUNCTION OPERATION |
The entry and start system has the following functions.
| Function | Outline |
| Mechanical key | Operation is same as conventional mechanical key |
| Wireless door lock control function | This function remotely locks and unlocks all doors or back door. Operation is same as wireless door lock control system. However, the receiver in certification ECU uses entry door control receiver to control locking and unlocking. |
| Entry illumination function | When person carrying key enters detection area, door will enter unlock standby mode and map light and foot light will illuminate |
| Entry unlock function | When key is located in detection area of door oscillator, door will unlock by touching inside of outside door handle |
| Entry lock function | When key is located in detection area of door oscillator and ignition switch is off, door can be locked by pressing lock switch on outside door handle |
| Key lock-in prevention function | Prevents confinement of key if door is locked using outside door handle while key is still inside vehicle |
| Warning function | When any of situations below occur, entry and start system causes certification ECU to sound buzzer in combination meter and wireless door lock buzzer in order to alert driver:
|
| Battery saving function | If key is constantly located within detection area of door oscillator, system maintains periodic communication with key. Therefore, if vehicle remains parked in that state for long time, key battery and vehicle battery could be drained. |
| Key cancel (Click here) | Following key functions can be canceled by following certain operations:
|
| WIRELESS DOOR LOCK AND UNLOCK AND BACK DOOR OPEN FUNCTION |
| ENTRY UNLOCK FUNCTION |
The detection area is formed by communication between a door electrical key oscillator and door control receiver when the door is locked in order to detect access of the person carrying the key.
When the person carrying the key enters the detection area around the vehicle, the matching of the ID codes for a door electrical key oscillator and key will automatically be performed. After the matching is completed, the door will enter unlock standby mode.
In unlock standby mode, the antenna built into the outside handle starts sensing. If the outside handle is held (the back side of the handle is touched), the door unlock operation will be performed. At this time, the hazard warning lights blink twice.
If none of the doors are opened within 30 seconds of a door unlock operation, all doors are automatically locked.
| ENTRY LOCK FUNCTION |
After leaving the vehicle carrying the key, push the lock switch on the outside handle when all the doors are closed.
The certification ECU determines whether the key is located inside or outside of the cabin based on the information from a door electrical key oscillator and indoor electrical key oscillator. Then matching of the ID codes is performed.
When the matching result shows that the ID codes of the key and indoor electrical key oscillator do not match and the ID codes of the key and door electrical key oscillator match, the door lock function will operate. At this time, the hazard warning lights blink once.
If the key is located inside of the cabin, the door lock function will not operate and the alarm buzzer (beep sound) will sound for 2 seconds.
| PREVENTION OF KEY CONFINEMENT FUNCTION |
If the user attempts to lock the door through keyless operation (move the lock knob to the lock position and then close the door) with the key in the cabin, the system determines that the key is located in the cabin and unlocks the door.
If the back door is closed with the key in it, the alarm will sound and the back door can be opened only when all the doors are locked in order to prevent key confinement in the vehicle.
| ENTRY ILLUMINATION FUNCTION |
| WARNING FUNCTION |
General:
When any of the situations below occur, the entry and start system causes the certification ECU to sound the buzzer in the combination meter and the wireless door lock buzzer, and illuminates the entry and start system warning light to alert the driver.
| Warning Function Operation Condition | Situation |
| Warning if occupant leaves with key | A |
| Warning if engine switch is operated while key is outside the detection area | B |
| Warning if entry lock is operated while key is inside vehicle | C |
| Warning if key battery is weak | D |
| Warning if clutch start switch malfunction has been detected | E |
Situation A:
In this situation, the following control is performed.
| Possible Effects without Warning | Engine cannot be restarted |
| Warning Condition | Certification ECU gives warning when all of following conditions are satisfied:
|
Combination Meter
| Warning:
|
| Wireless Door Lock Buzzer | Warning: Sounds 3 times Warning is stopped when one of following conditions is met
|
Situation B:
In this situation, the following control is performed.
| Possible Effects without Warning | Confuses the user |
| Warning Condition | Certification ECU gives warning when all of following conditions are satisfied:
|
Combination Meter
| Warning:
|
Situation C:
In this situation, the following control is performed.
| Possible Effects without Warning | Vehicle theft |
| Warning Condition | Certification ECU gives a warning when all of following conditions are satisfied:
|
| Wireless Door Lock Buzzer | Warning: Sounds for 2 seconds |
Situation D:
In this situation, the following control is performed.
| Possible Effects without Warning | Entry and start system does not function |
| Warning Condition | Certification ECU gives warning when all of following conditions are satisfied:
|
Combination Meter
| Warning:
|
Situation E (for Manual transaxle):
In this situation, the following control is performed.
| Possible Effects without Warning | Engine cannot be started |
| Warning Condition | Certification ECU gives a warning when all of following conditions are satisfied:
|
| Engine Switch Indicator Light | Blinks in green in 1 second cycles |
| BATTERY SAVING |
Vehicle battery saving function:
In the entry and start system, signals are emitted outside of the vehicle at a prescribed interval (0.25 seconds) when the doors are locked. Therefore, the vehicle battery could be drained if the vehicle remains parked for a long time. For this reason, the controls listed below are affected.
| Condition | Control |
Both conditions below are met for 5 days:
| Signal transmission interval time is extended |
Both conditions below are met for 14 days:
| Automatically deactivates the entry and start system |
Key battery and vehicle battery saving function:
In the entry and start system, if the electrical key is constantly located within the vehicle exterior detection area of the doors, the system maintains periodic communication with the electrical key. Therefore, if the vehicle remains parked in that state for a long time, the electrical key battery and the vehicle battery could be drained. For this reason, if this state continues longer than 10 minutes, the entry and start system automatically becomes deactivated.
Reinstatement conditions: