Home › BODY › SLIDING ROOF › SLIDING ROOF SYSTEM

SLIDING ROOF SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Read the Data List according to the display on the tester.

    Sliding roof ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Close Switch
    Slide switch close signal / ON or OFF
    ON: TILT UP switch is pressed
    OFF: TILT UP switch is not pressed
    -
    Open Switch
    Slide switch open signal / ON or OFF
    ON: SLIDE OPEN switch is pressed
    OFF: SLIDE OPEN switch is not pressed
    -
    Ignition (MPX)
    Ignition switch signal (MPX signal) / ON or OFF
    ON: Ignition switch is on (IG)
    OFF: Ignition switch is off
    -
    Ignition (Direct Signal)
    Ignition switch signal (Direct signal) / ON or OFF
    ON: Ignition switch is on (IG)
    OFF: Ignition switch is off
    -
    Key Off Permission
    Key off permission / ON or OFF
    ON: Ignition switch is on (IG)
    OFF: Ignition switch is off
    -
    Hall IC1 Status
    Sliding roof operating signal / NORMAL or LOCK
    NORMAL: Sliding roof motor is operating
    LOCK: Sliding roof motor is not operating
    -
    Hall IC1 Pulse
    Sliding roof operating signal / LO or HI
    LO: Sliding roof motor is not operating
    HI: Sliding roof motor is operating
    -
    Hall IC2 Status
    Sliding roof operating signal / NORMAL or LOCK
    NORMAL: Sliding roof motor is operating
    LOCK: Sliding roof motor is not operating
    -
    Hall IC2 Pulse
    Sliding roof operating signal / LO or HI
    LO: Sliding roof motor is not operating
    HI: Sliding roof motor is operating
    -
    Open Switch Failure (Current)
    SLIDE OPEN switch condition (current) / Fail or Not Fail
    Fail: SLIDE OPEN switch is stuck
    Not Fail: SLIDE OPEN switch is not stuck
    -
    Close Switch Failure (Current)
    TILT UP switch condition (current) / Fail or Not Fail
    Fail: TILT UP switch is stuck
    Not Fail: SLIDE OPEN switch is not stuck
    -
    Open Switch Failure (Past)
    SLIDE OPEN switch condition (past) / Fail or Not Fail
    Fail: SLIDE OPEN switch was stuck in past
    Not Fail: SLIDE OPEN switch was not stuck in past
    -
    Close Switch Failure (Past)
    TILT UP switch condition (past) / Fail or Not Fail
    Fail: TILT UP switch was stuck in past
    Not Fail: TILT UP switch was not stuck in past
    -

    Main body ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Communication Slide Roof
    Communication status between sliding roof drive gear sub-assembly (sliding roof ECU) and main body ECU / OK or STOP
    OK: Connection
    STOP: No connection
    -


PERFORM ACTIVE TEST

HINT:
Performing the intelligent tester's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Perform the Active Test according to the display on the tester.

    Sliding roof ECU 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Slide Roof
    Operate sliding roof
    Clos / Up / OFF
    -
    Slide Roof
    Operate sliding roof
    Opn / Dwn / OFF
    -