WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System) > TERMINALS OF ECU |
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |


Disconnect the IB and IE junction block connectors.
Measure the resistance and voltage of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND1 (IE-17) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| BECU (IB-30) - GND1 (IE-17) | R - W-B | Battery (power supply) | Always | 10 to 14 V |
Reconnect the IB and IE junction block connectors.
Measure the voltage of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| DCTY (IA-21)*1 - Body ground DCTY (IC-6)*2 - Body ground | W*1 - Body ground BR*2 - Body ground | Driver side door courtesy switch input | Driver side door closed | 10 to 14 V |
| Driver side door open | Below 1 V | |||
| PCTY (IC-14)*1 - Body ground PCTY (IA-24)*2 - Body ground | BR*1 - Body ground W*2 - Body ground | Passenger side door courtesy switch input | Passenger side door closed | 10 to 14 V |
| Passenger side door open | Below 1 V | |||
| RCTY (ID-7) - Body ground | LG - Body ground | Rear RH door courtesy switch input | Rear RH door closed | 10 to 14 V |
| Rear RH door open | Below 1 V | |||
| LCTY (B18-8) - Body ground | SB - Body ground | Rear LH door courtesy switch input | Rear LH door closed | 10 to 14 V |
| Rear LH door open | Below 1 V | |||
| B+ (IA-7) - Body ground | LG- Body ground | Back door courtesy switch input | Back side door closed | 10 to 14 V |
| Back side door open | Below 1 V | |||
| L1 (IH-4)*1 - Body ground L1 (IH-13)*2 - Body ground | P*1 - Body ground V*2 - Body ground | Door lock motor LOCK drive output | Master switch (door control switch) OFF | Below 1 V |
| Master switch (door control switch) ON (LOCK) | 10 to 14 V → Below 1 V | |||
| UL1 (IH-5)*1 - Body ground UL1 (IH-14)*2 - Body ground | B*1 - Body ground O*2 - Body ground | Door lock motor UNLOCK drive output | Master switch (door control switch) OFF | Below 1 V |
| Master switch (door control switch) ON (UNLOCK) | 10 to 14 V → Below 1 V | |||
| ACT+ (IH-8)*1 - Body ground ACT+ (IH-17)*2 - Body ground | R - Body ground | Door lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| Master switch (door control switch) or driver side door key cylinder ON (LOCK) | 10 to 14 V → Below 1 V | |||
| ACT- (IH-18)*1 - Body ground ACT- (IH-9)*2 - Body ground | B - Body ground | Door lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| Master switch (door control switch) or driver side door key cylinder ON (UNLOCK) | 10 to 14 V → Below 1 V | |||
| LSWD (E18-25) - Body ground | Y - Body ground | Driver side door lock position switch input | Driver side door UNLOCK | Below 1 V |
| Driver side door LOCK | 10 to 14 V | |||
| LSWP (E18-10) - Body ground | Y - Body ground | Passenger side door lock position switch input | Passenger side door UNLOCK | Below 1 V |
| Passenger side door LOCK | 10 to 14 V | |||
| UL2 (IH-6)*1 - Body ground UL2 (IH-15)*2 - Body ground | LG*1 - Body ground L*2 - Body ground | Door lock motor UNLOCK drive output | Passenger side door key cylinder OFF | Below 1 V |
| Passenger side door key cylinder ON (UNLOCK) | 10 to 14 V → Below 1 V | |||
| L2 (IH-7)*1 - Body ground L2 (IH-16)*2 - Body ground | SB*1 - Body ground R*2 - Body ground | Door lock motor LOCK drive output | Master switch or driver side door key cylinder OFF | Below 1 V |
| Master switch or driver side door key cylinder ON (LOCK) | 10 to 14 V → Below 1 V | |||
| HAZ (IS-17) - Body ground | GR - Body ground | Hazard warning light signal | Answer-back ON | Pulse generation |
| Answer-back OFF | 10 to 14 V |
| CHECK CERTIFICATION ECU |

Disconnect the E63 ECU connector.
Measure the resistance and voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E (E63-17) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| +B1 (E63-1) - Body ground | R - Body ground | +B power supply | Always | 10 to 14 V |
| IG (E63-18) - Body ground | B - Body ground | Ignition power supply | Ignition switch on (IG) | 10 to 14 V |
| Ignition switch off | Below 1 V | |||
| LIN (E63-10) - Body ground | V - Body ground | LIN line | Always | 10 kΩ or higher |
Reconnect the E63 ECU connector.
Measure the voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| RSSI (E63-39) - E (E63-17) | R - W-B | Door control receiver electric wave existence signal | Ignition switch off, all doors closed and transmitter switch not pressed | 10 to 14 V |
| Ignition switch off, all doors closed and transmitter switch pressed | Below 1 V | |||
| RDA (E63-38) - E (E63-17) | Y - W-B | Door control receiver data input signal | Ignition switch off, all doors closed and transmitter switch not pressed | Below 1 V |
| Ignition switch off, all doors closed and transmitter switch pressed | 10 to 14 V | |||
| RCO (E63-29) - E (E63-17) | V - W-B | Door control receiver power source | Ignition switch off, all doors closed and transmitter switch not pressed | Below 1 V |
| Ignition switch off, all doors closed and transmitter switch pressed | 4.6 to 5.4 V |