ENGINE UNIT > REPLACEMENT |
| 1. REPLACE SPARK PLUG TUBE GASKET |
![]() |
Pry up the claws of the ventilation baffle plate.
![]() |
Using a screwdriver with its tip taped and a hammer, tap out the 6 spark plug tube gaskets.
![]() |
Using a 32 mm socket wrench, tap in 6 new spark plug tube gaskets to the head covers.
Return the claws of the ventilation baffle plate to its original positions.
| 2. REPLACE TIMING CHAIN COVER OIL SEAL |
![]() |
Using a screwdriver, pry out the oil seal.
![]() |
Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.
Apply MP grease to the lip of the oil seal.
| 3. REPLACE ENGINE REAR OIL SEAL |
![]() |
Place the oil seal retainer on wooden blocks.
Using a screwdriver and a hammer, tap out the oil seal.
![]() |
Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge.
| 4. REPLACE INTAKE VALVE GUIDE BUSH |
Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).
Place the cylinder head on wooden blocks.
![]() |
Using SST and a hammer, tap out the valve guide bush.
![]() |
Using a caliper gauge, measure the bush bore diameter of the cylinder head.
Select a new guide bush (STD or O/S 0.05).
| Bush Size | Specified Condition |
| Use STD | 10.335 to 10.356 mm (0.4069 to 0.4077 in.) |
| Use O/S 0.05 | 10.285 to 10.306 mm (0.4049 to 0.4057 in.) |
Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).
![]() |
Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
![]() |
Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.
| 5. REPLACE EXHAUST VALVE GUIDE BUSH |
Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).
Place the cylinder head on wooden blocks.
![]() |
Using SST and a hammer, tap out the valve guide bush.
![]() |
Using a caliper gauge, measure the bush bore diameter of the cylinder head.
Select a new guide bush (STD or O/S 0.05).
| Bush Size | Specified Condition |
| Use STD | 10.335 to 10.356 mm (0.4069 to 0.4077 in.) |
| Use O/S 0.05 | 10.285 to 10.306 mm (0.4049 to 0.4057 in.) |
Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).
![]() |
Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
![]() |
Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.
| 6. REPLACE CYLINDER BLOCK STUD BOLT |
Remove the stud bolts.

Using an E8 "TORX" socket wrench, install the stud bolts.
| 7. REPLACE CYLINDER BLOCK STRAIGHT PIN |
Remove the straight pin.

Using a plastic-faced hammer, tap in new straight pins to the cylinder block.
| Item | Specified Condition |
| Pin A | 23 mm (0.91 in.) |
| Pin B | 6 mm (0.24 in.) |
| Pin C | 11 mm (0.43 in.) |
| Pin D | 9 mm (0.35 in.) |
| 8. REPLACE CYLINDER HEAD RING PIN |
![]() |
Remove the ring pins.
Using a plastic-faced hammer, tap in a new ring pin until the pin stops.
| 9. REPLACE CYLINDER HEAD STUD BOLT |
Remove the stud bolts.

Using E6 and E8 "TORX" socket wrenches, install the stud bolts.
| 10. REPLACE CYLINDER HEAD SET STRAIGHT PIN |
Using a plastic-faced hammer, tap in a new straight pin as shown in the illustration.
