ELECTRONIC POWER STEERING SYSTEM > FREEZE FRAME DATA |
| FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and check the freeze frame data by following the prompts on the intelligent tester display.
| Tester Display | Measurement Item/Range | Normal Condition | Reference Value |
| Meter Vehicle Velocity | Vehicle speed from meter: Min.: 0 km/h (0 mph) Max.: 300 km/h (187.5 mph) | Vehicle stopped | 0 km/h (0 mph) |
| Vehicle driven at constant speed | No significant fluctuation | ||
| Engine Revolution | Show the engine revolution: Min.: 0 rpm Max.: 12800 rpm | Engine is running at a constant speed | No significant fluctuation |
| Motor Actual Current | Amount of current to motor: Min.: -327.68 A Max.: 327.67 A | Power steering is in operation | Value changes in proportion to steering effort |
| Command Value Current | Demanded amount of current to motor: Min.: -327.68 A Max.: 327.67 A | Power steering is in operation | Value changes in proportion to steering effort |
| Steering Angle Velocity | Steering angle speed: Min.: -32768 deg/s Max.: 32767 deg/s | Steering wheel is turned | Value changes in proportion to steering effort |
| Thermistor Temperature | ECU substrate temperature: Min.: -40°C Max.: 150°C | Ignition switch on (IG) | - |
| PIG Power Supply | Power source voltage to activate motor: Min.: 0 V Max.: 20.1531 V | Power steering in operation | 10 to 14 V |
| IG Power Supply | ECU power source voltage: Min.: 0 V Max.: 20.1531 V | Ignition switch on (IG) | 10 to 14 V |
| Steering Wheel Torque | Steering wheel torque: Min.: -327.68 Nm Max.: 7 Nm | - | - |
| Motor Rotation Angle | Motor rotation angle: Min.: 0 deg Max.: 1441.77 deg | Power steering in operation | During steering operation, motor rotation angle value changes from 0 to 360° |
| Motor Voltage | Motor power supply voltage: Min.: 0 V Max.: 98 V | Power steering in operation | - |
| Motor Terminal Volt (U) | Motor terminal voltage (U phase): Min.: 0 V Max.: 98 V | Engine running and steering wheel turned | When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed. |
| Motor Terminal Volt (V) | Motor terminal voltage (V phase): Min.: 0 V Max.: 98 V | Engine running and steering wheel turned | When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed. |
| Motor Terminal Volt (W) | Motor Terminal voltage (W phase): Min.: 0 V Max.: 98 V | Engine running and steering wheel turned | When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed. |
| Torque Sensor 1 Output | Torque sensor 1 output voltage/ Min.: 0 V Max.: 5 V | 2.3 to 2.7 V | Steering wheel is not turned (without load) |
| 2.5 to 4.04 V | Steering wheel is turned to the right when the vehicle is stopped | ||
| 0.95 to 2.5 V | Steering wheel is turned to the left when the vehicle is stopped | ||
| Torque Sensor 2 Output | Torque sensor 2 output voltage/ Min.: 0 V Max.: 5 V | 2.3 to 2.7 V | Steering wheel is not turned (without load) |
| 0.95 to 2.5 V | Steering wheel is turned to the right when the vehicle is stopped | ||
| 2.5 to 4.04 V | Steering wheel is turned to the left when the vehicle is stopped | ||
| Battery Voltage | Battery voltage: Min.: 0 V Max.: 25.5 V | - | 10 to 14 V |
| PS Assist Signal | Power steering assist signal: ON or OFF | - | - |