Home › TRANSMISSION ยท U241E AUTOMATIC TRANSAXLE › DIFFERENTIAL CASE

DIFFERENTIAL CASE > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL SIDE GEAR


    C083137E01
  1. Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF, and install them to the differential case.



2. INSTALL NO. 1 FRONT DIFFERENTIAL PINION SHAFT


    C083135E01
  1. Coat the front differential pinion shaft with ATF, and install it to the differential case.



3. INSPECT FRONT DIFFERENTIAL SIDE GEAR BACKLASH


    C083138E01
  1. Using a dial indicator, measure the backlash of the side gear.

    Standard backlash:
    0.05 to 0.20 mm (0.0020 to 0.0070 in.)

    Standard thrust washer thickness:
    Thickness
    Thickness
    1.0 mm (0.0394 in.)
    1.2 mm (0.0472 in.)
    1.1 mm (0.0433 in.)
    1.3 mm (0.0512 in.)



4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN


    C060005E01
  1. Using a pin punch and hammer, tap in the pinion shaft straight pin.



    C060006E01
  1. Using a chisel and hammer, stake the differential case.



5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


    D025218E03
  1. Using SST and a press, press in the front differential case tapered roller bearing rear inner race to the differential case.

    SST
    09608-06041  



    D025219E02
  1. Using SST and a hammer, tap in the case washer and front differential case tapered roller bearing rear outer race to the transaxle case.

    SST
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)



6. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    D025216E01
  1. Using SST and a press, press in the front differential case tapered roller bearing front inner race to the differential case.

    SST
    09608-06041  



    D025217E01
  1. Using SST and a hammer, tap in the front differential case tapered roller bearing front outer race to the transaxle housing.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07100)
    09950-60010   (09951-00340)



7. INSTALL FRONT DIFFERENTIAL RING GEAR


    D025215E03
  1. Using ATF and heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).

  1. Clean the contact surface of the front differential case.



    C083132E02
  1. Align the matchmarks, and install the front differential ring gear case quickly.



    C083133E01
  1. Tighten the 10 bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



8. INSPECT TAPERED ROLLER BEARING PRELOAD


    C083139E01
  1. Install the differential assembly to the transaxle case.

  1. Install the transaxle housing to the transaxle case.



    C050259E01
  1. Install the 16 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf } for bolt A
    29 N*m{ 296 kgf*cm , 21 ft.*lbf } for bolt B and C

    HINT:
    Each bolt length is indicated below.

    Bolt length:
    50 mm (1.97 in.) for bolt A and B
    42 mm (1.65 in.) for bolt C



    C083572E01
  1. Using SST, turn the differential.

    SST
    09564-32011  



    C083572E01
  1. Using SST and torque wrench, measure the preload of the differential.

    SST
    09564-32011  

    Torque:
    Standard turning torque at 60 rpm:
    0.20 to 0.69 N*m{ 2.0 to 7.0 kgf*cm , 1.8 to 6.1 in.*lbf } for new
    0.10 to 0.35 N*m{ 1.0 to 3.6 kgf*cm , 0.9 to 3.1 in.*lbf } for used

    Standard adjusting shim thickness:
    Mark
    Thickness
    0
    1.90 mm (0.074 in.)
    1
    1.95 mm (0.077 in.)
    2
    2.00 mm (0.079 in.)
    3
    2.05 mm (0.081 in.)
    4
    2.10 mm (0.083 in.)
    5
    2.15 mm (0.085 in.)
    6
    2.20 mm (0.087 in.)
    7
    2.25 mm (0.089 in.)
    8
    2.30 mm (0.091 in.)
    9
    2.35 mm (0.093 in.)
    A
    2.40 mm (0.094 in.)
    B
    2.45 mm (0.096 in.)
    C
    2.50 mm (0.098 in.)
    D
    2.55 mm (0.100 in.)
    E
    2.60 mm (0.102 in.)
    F
    2.65 mm (0.104 in.)
    G
    2.70 mm (0.106 in.)
    H
    2.75 mm (0.108 in.)
    J
    2.80 mm (0.110 in.)



    D009182E01
  1. Remove the 16 bolts.

  1. Using a practic-faced hammer, remove the transaxle housing.



    C083139E01
  1. Remove the differential.



9. INSTALL TRANSAXLE HOUSING OIL SEAL


D025606E01
  1. Coat the lip of a new oil seal with a little amount of MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09350-32014   (09351-32150)
    09950-70010   (09951-07150)



10. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL


D025605E01
  1. Coat the lip of a new oil seal with a little amount of MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09350-32014   (09351-32150)
    09950-70010   (09951-07150)