Home › TRANSMISSION ยท U241E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Remove the bolt and hole cover from the transaxle.

  1. Remove the O-ring from the hole cover.



2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    D008032E01
  1. Remove the nut, washer and control shaft lever.



    D008033E01
  1. Using a screwdriver, unstake the lock plate and remove the lock nut and lock plate.



    D008034E03
  1. Remove the 2 bolts and pull out the park/neutral position switch.



3. REMOVE BREATHER PLUG HOSE
  1. Remove the breather plug hose from the breather plug.



4. REMOVE OIL COOLER OUTLET TUBE UNION


C127449
  1. Remove the union.

  1. Remove the O-ring from the union.



5. REMOVE OIL COOLER INLET TUBE UNION


C127450
  1. Remove the union.

  1. Remove the O-ring from the union.



6. REMOVE SPEED SENSOR


    D003900E01
  1. Remove the 2 bolts and 2 speed sensors from the transaxle.

  1. Remove the 2 O-rings from the sensors.



7. REMOVE NO. 1 TRANSAXLE CASE PLUG


    C134982
  1. Remove the 4 plugs from the transaxle.

  1. Remove the 4 O-rings from the 4 plugs.



8. FIX AUTOMATIC TRANSAXLE ASSEMBLY


D009176E01


9. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    D009177E01
  1. Remove the 18 bolts.

  1. Remove the oil pan and 3 magnets.

  1. Remove the gasket from the oil pan.



10. INSPECT AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    AT00103E01
  1. Remove the magnets and use them to collect any steel chips. Examine the clips and particles in the pan and on the magnet to determine what type of wear has occurred in the transaxle.
    Steel (magnetic): bearing, gear and plate wear
    Brass (non-magnetic): bush wear



11. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    D009179E01
  1. Remove the 3 bolts and oil strainer.



    D009180E01
  1. Remove the O-ring from the oil strainer.



12. REMOVE TRANSMISSION WIRE


    C130917E01
  1. Remove the 5 connectors from the shift solenoid valves.

  1. Remove the bolt, clamp and ATF temperature sensor.



    D003547E08
  1. Remove the bolt and transaxle solenoid wire from the transaxle.



    D003636E03
  1. Remove the O-ring from the transaxle solenoid wire.



13. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    D003553E01
  1. Support the valve body assembly and remove the 17 bolts and the valve body assembly.



14. REMOVE NO. 1 GOVERNOR APPLY GASKET


    C083127E01
  1. Remove the governor apply gasket from the transaxle.



15. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET


    C083128E01
  1. Remove the 2nd brake gasket from the transaxle.



16. REMOVE BRAKE DRUM GASKET


    C083129E01
  1. Remove the brake drum gasket from the transaxle.



17. REMOVE CHECK BALL BODY


    D003554E02
  1. Remove the check ball body and spring from the transaxle.



18. REMOVE C-3 ACCUMULATOR PISTON


    D003555E01
  1. Remove the compression spring from the C-3 accumulator piston.



    D003556E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.



    D003902E02
  1. Remove the O-ring from the C-3 accumulator piston.



19. REMOVE C-1 ACCUMULATOR PISTON


    D003557E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-1 accumulator piston and compression spring.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.



    D003903E01
  1. Remove the 2 O-rings from the C-1 accumulator piston.



20. REMOVE B-3 ACCUMULATOR PISTON


    D003558E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-3 accumulator piston and 2 compression springs.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.



    D003904E05
  1. Remove the O-ring from the B-3 accumulator piston.



21. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY


    D003560E03
  1. Remove the 2 bolts, manual detent spring and cover.



22. REMOVE PARKING LOCK PAWL BRACKET


    C056727E01
  1. Remove the 2 bolts and parking lock pawl bracket.



23. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING


    D003559E01
  1. Using needle-nose pliers, remove the retainer spring.



24. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


    D003563E01
  1. Using a chisel and hammer, unstake and remove the manual valve lever spacer.



    D003564E01
  1. Using a pin punch and hammer, tap out the manual valve lever shaft spring pin.

    HINT:
    Slowly drive out the pin so that it will not fall into the transaxle.



    D003565E02
  1. Remove the manual valve lever shaft and manual valve lever.



25. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    D003905E01
  1. Remove the parking lock rod from the manual valve lever.



26. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    D003566E02
  1. Using a screwdriver, pry out the oil seal from the transaxle.



27. INSPECT INPUT SHAFT END PLAY
  1. Fix the transaxle case with the oil pump side facing up.



    D008046E01
  1. Using a dial indicator, measure the input shaft end play.

    Standard end play:
    0.26 to 1.25 mm (0.0103 to 0.0492 in.)



28. REMOVE NO. 1 TRANSAXLE CASE PLUG


    C134983
  1. Remove the 2 plugs.

  1. Remove the 2 O-rings from the plug.



29. REMOVE TRANSAXLE HOUSING


    D009182E01
  1. Remove the 16 bolts.

  1. Tap on the circumference of the transaxle housing with a plastic-faced hammer to remove the transaxle housing from the transaxle.

    NOTICE:
    Differential may be accidentally removed when the transaxle housing is removed.



30. REMOVE UNDERDRIVE CYLINDRICAL ROLLER BEARING


    D003606E02
  1. Using SST, remove the cylindrical roller bearing from the transaxle.

    SST
    09514-35011  



31. REMOVE UNDERDRIVE OUTPUT SHAFT OIL SEAL RING


    D003915E07
  1. Remove the oil seal ring from the transaxle housing.



32. REMOVE OIL PUMP ASSEMBLY


    D003569E03
  1. Remove the 7 bolts and oil pump assembly from the transaxle.



33. REMOVE THRUST NEEDLE ROLLER BEARING


    D025505E03
  1. Remove thrust needle roller bearing from the underdrive planetary gear.



34. REMOVE NO. 2 THRUST BEARING UNDERDRIVE RACE


    D025506E04
  1. Remove the thrust bearing race from the underdrive planetary gear.



35. REMOVE FRONT DIFFERENTIAL ASSEMBLY


    D003577E01
  1. Remove the front differential from the transaxle.



36. REMOVE OVERDRIVE BRAKE GASKET


    D003573E01
  1. Remove the 2 overdrive brake gaskets from the transaxle.



37. REMOVE FORWARD CLUTCH ASSEMBLY


    D003574E03
  1. Remove the forward clutch from the transaxle.



    D003906E02
  1. Remove the thrust bearing from the forward clutch.



38. REMOVE MULTIPLE DISC CLUTCH CLUTCH HUB


    D003575E01
  1. Remove the thrust bearing, multiple clutch hub, needle roller bearing and bearing race from the transaxle.



39. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY


    D003576E03
  1. Remove the bolt and parking pawl shaft clamp.



    D009201E01
  1. Remove the parking lock pawl shaft.



    D008048E01
  1. Push the parking lock pawl.

    HINT:
    Failure to do so will cause the interference when the underdrive planetary gear is removed.



    D003579E04
  1. Remove the underdrive planetary gear from the transaxle.

    NOTICE:
    Be careful so that the underdrive planetary gear assembly will not fall out.



    D008049E01
  1. Remove the spring, pawl pin and parking lock pawl.



40. REMOVE UNDERDRIVE CLUTCH ASSEMBLY


    D003580E02
  1. Remove the underdrive clutch assembly, needle roller bearing, thrust bearing underdrive race from the transaxle.



41. REMOVE UNDERDRIVE 1-WAY CLUTCH ASSEMBLY


    D003581E02
  1. Using a screwdriver, pry out the snap ring from the transaxle.



    D003627E03
  1. Remove the 1-way clutch from the transaxle.



    D009198E01
  1. Remove the outer race retainer from the 1-way clutch.



42. REMOVE NO. 2 UNDERDRIVE CLUTCH DISC


    D008050E01
  1. Using a screwdriver, pry out the snap ring from the transaxle.



    D009197E01
  1. Remove the flange, 3 discs and 3 plates from the transaxle.



43. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC


D009196E01
Check to see if the sliding surface of the disc, plate and flange are worn or burnt.
If necessary, replace them.

NOTICE:
  1. If the lining of the disc is peeling off or discolored, or even if a part of the groove is defaced, replace all discs.
  2. Before assembling new discs, soak them in ATF for at least 15 minutes.



44. REMOVE UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    D003610E01
  1. Using SST, a snap ring expander and press, remove the snap ring from the transaxle.

    SST
    09387-00020  



    D008051E01
  1. Remove the underdrive brake return spring from the underdrive brake piston.



45. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    D003806E01
  1. Using a vernier caliper, measure the free length of the underdrive brake return spring together with the spring seat.

    Standard free length:
    14.04 mm (0.5213 in.)



46. REMOVE UNDERDRIVE CLUTCH DRUM OIL SEAL RING


    D003914E04
  1. Remove the 2 oil seal rings from the transaxle.



47. REMOVE NO. 1 TRANSAXLE CASE PLUG


    C134984
  1. Remove the 2 plugs from the transaxle rear cover.

  1. Remove the 2 O-rings from the 2 plugs.



48. REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY


    D009943E02
  1. Remove the 11 bolts.

  1. Tap the circumference of the rear cover with a plastic-faced hammer to remove the transaxle rear cover from the transaxle.



    D009184E01
  1. Remove the 2 outer rear clutch oil seal rings from the transaxle rear cover.



    C083140E01
  1. Using a T30 ''torx'' socket wrench, remove the 2 screws and transaxle rear cover plate.



    D003801E01
  1. Using SST, remove the needle-roller bearing from the transaxle rear cover.

    SST
    09387-00041   (09387-01010, 09387-01030, 09387-01040)



49. REMOVE UNDERDRIVE BRAKE PISTON


    D003799E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the underdrive brake piston.



    D003794E02
  1. Remove the 2 O-rings from the underdrive brake piston.



50. REMOVE BRAKE APPLY TUBE


    D025510E01
  1. Remove the bolt, clamp and 2 brake apply tubes.

  1. Remove the brake apply tube from the clamp.



51. REMOVE FRONT CLUTCH APPLY TUBE


52. REMOVE NO. 1 GOVERNOR APPLY GASKET


    D003591E01
  1. Using a screwdriver, remove the 2 governor apply gaskets.



53. REMOVE DIRECT CLUTCH ASSEMBLY


    D003586E01
  1. Remove the thrust bearing and direct clutch from the transaxle.



    D008053E01
  1. Remove the bearing race from the direct clutch.



54. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


    D003587E01
  1. Remove the rear planetary sun gear from the transaxle.



    D003791E01
  1. Remove the rear planetary sun gear thrust bearing from the rear planetary sun gear.



    D008054E01
  1. Remove the No. 1 thrust washer and 1-way clutch thrust bearing from the rear planetary sun gear.



55. REMOVE 1-WAY CLUTCH ASSEMBLY


    D008055E01
  1. Remove the 1-way clutch from the transaxle.



    D003909E02
  1. Remove the 1-way clutch inner race from the 1-way clutch.



56. REMOVE 1-WAY CLUTCH SLEEVE OUTER


D003589E03


57. REMOVE 2ND BRAKE CLUTCH DISC
  1. Using a screwdriver, remove the 2nd brake hole snap ring.



    C129388
  1. Remove the flange, 3 discs and 3 plates from the transaxle.



58. INSPECT 2ND BRAKE CLUTCH DISC


    D004083E01
  1. Check to see if the sliding surface of the disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc is peeling off or discolored, or even if a part of the printed number is defaced, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.



59. REMOVE 2ND BRAKE PISTON ASSEMBLY


    D008058E03
  1. Using a screwdriver, pry out the snap ring.



    D008059E01
  1. Remove the 2nd brake piston from the transaxle.



60. REMOVE 1ST AND REVERSE BRAKE CLUTCH DISC


    D009941E01
  1. Remove the flange, 5 discs and 5 plates from the transaxle.



61. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC


    D009189E01
  1. Check to see if the sliding surface of the disc, plate and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc is peeling off or discolored, or even if a part of the groove is defaced, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.



62. REMOVE REAR PLANETARY GEAR ASSEMBLY


    D003616E02
  1. Using a screwdriver, pry out the snap ring from the brake hub.



    D008062E01
  1. Remove the rear planetary gear from the transaxle.



    D003910E01
  1. Remove the thrust washer from the rear planetary gear.



    D003593E01
  1. Remove the thrust bearing race from the rear planetary gear.



63. REMOVE INPUT SUN GEAR


    D003873E03
  1. Remove the 2 thrust bearings, bearing race and input sun gear from the transaxle.



64. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    D003595E02
  1. Using a chisel and hammer, unstake the lock washer.

    NOTICE:
    Push down all claws of the washer. Otherwise SST cannot be fully pressed against the nut and cannot loosen the nut.



    D003596E01
  1. Using SST, remove the nut.

    SST
    09387-00030  
    09387-00080  



    D003597E01
  1. Using SST and a press, remove the front planetary gear from the counter drive gear.

    SST
    09950-60010   (09951-00450)



    D008063E01
  1. Remove the front planetary gear from the brake hub.



65. REMOVE FRONT PLANETARY RING GEAR


    D003615E03
  1. Using a screwdriver, pry out the brake hub snap ring and front planetary ring gear from the brake hub.



66. REMOVE 1ST AND REVERSE BRAKE PISTON


    D003600E01
  1. Using SST, a press and ring expander, remove the snap ring and piston return spring.

    SST
    09387-00070  

    NOTICE:
    1. Stop the press when the spring sheet is lowered 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove, preventing the spring sheet from deforming.
    2. Do not expand the snap ring excessively.



    D008061E01
  1. Remove the 1st and reverse brake return spring from the 1st and reverse brake piston.



    D003800E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle to remove the 1st and reverse brake piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump out. When removing the piston, hold it with your hand using a waste cloth.
    2. Make sure not to spatter ATF when applying compressed air.



    D003913E01
  1. Remove the 2 O-rings from the 1st and reverse brake piston.



67. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    D003811E01
  1. Using a vernier caliper, measure the free length of the 1st and reverse brake return spring together with the spring seat.

    Standard free length:
    15.51 mm (0.6106 in.)



68. REMOVE COUNTER DRIVE GEAR


    D003601E01
  1. Using SST and a press, press out the counter drive gear from the transaxle.

    SST
    09950-60010   (09951-00600)
    09950-70010   (09951-07100)



    D003602E01
  1. As shown in the illustration, tighten the 2 bolts evenly and make a clearance of approximately. 20.0 mm (0.797 in.) between the counter drive gear and the inner race.



    D003603E02
  1. Using SST, remove the tapered roller bearing.

    SST
    09950-60010   (09951-00600)
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09958-04011)



    D003798E01
  1. Using a brass bar and hammer, tap out the 2 counter drive gear bearing outer races from the transaxle.



69. REMOVE COUNTER DRIVE GEAR HOLE SNAP RING


    D003604E01
  1. Using a screwdriver, pry out the snap ring from the transaxle.



70. REMOVE NO. 2 BREATHER PLUG


71. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


    D003607E01
  1. Remove the bolt, the transaxle apply tube clamp and the differential gear lube apply tube from the transaxle.