RADIATOR > INSTALLATION |
| 1. INSTALL FAN SHROUD WITH COOLING FAN |
![]() |
Install the fan shroud with cooling fan to the radiator with the 2 bolts.
| 2. INSTALL RADIATOR ASSEMBLY |
Install the 4 fan shroud cushions to the cooler condenser.
Set the cooler condenser to the fan shroud.
![]() |
Install the 2 radiator support lower cushions to the fan shroud.
Install the radiator with cooler condenser and fan shroud to the radiator support lower.
| 3. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY |
![]() |
Install the upper radiator support with the 4 bolts.
| 4. INSTALL NO. 2 FAN SHROUD |
![]() |
Attach the 2 claws to install the No. 2 fan shroud and install the 2 bolts.
| 5. INSTALL UPPER RADIATOR SUPPORT BRACKET |
![]() |
Install the bracket with the 2 bolts.
| 6. CONNECT HORN CONNECTOR |
Connect the 2 horn connectors.
| 7. CONNECT NO. 2 WATER BY-PASS HOSE |
Connect the by-pass hose to the radiator and radiator reservoir.
| 8. CONNECT NO. 2 RADIATOR HOSE |
| 9. CONNECT NO. 1 RADIATOR HOSE |

| 10. CONNECT NO. 2 TRANSMISSION OIL COOLER HOSE (for Automatic Transaxle) |
Connect the oil cooler hose for U241E (2WD) .
Connect the oil cooler hose for U140F (4WD) .
| 11. CONNECT NO. 1 TRANSMISSION OIL COOLER HOSE (for Automatic Transaxle) |
Connect the oil cooler hose for U241E (2WD) .
Connect the oil cooler hose for U140F (4WD) .
| 12. CONNECT COOLING FAN MOTOR HARNESS |
Attach the harness with the 5 clamps.
Connect the 2 fan motor connectors.

| 13. INSTALL NO. 1 WATER BY-PASS PIPE |
Install the by-pass pipe with the 2 bolts to the upper radiator support.
Connect the No. 1 radiator hose to the pipe.
| 14. CONNECT NO. 5 WATER BY-PASS HOSE |
Connect the by-pass hose to the radiator.
| 15. CONNECT NO. 1 WATER BY-PASS HOSE |
Connect the by-pass hose to the radiator and radiator reservoir.

| 16. CONNECT HOOD LOCK SWITCH CONNECTOR |
![]() |
| 17. INSTALL RADIATOR GRILLE SUB-ASSEMBLY |
![]() |
Attach the 7 claws and guide to install the radiator grille.
![]() |
Install the 3 bolts and 3 nuts.
| 18. INSTALL BATTERY |
| 19. INSTALL BATTERY CLAMP |
Attach the hook of the battery clamp to the battery bracket.
Temporarily tighten the nut and install the bolt.
Adjust the battery clamp's position.
Fully tighten the bolt and nut.
| 20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 21. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.
![]() |
Continue adding TOYOTA SLLC until it is filled to the B line at the base of the reservoir's filler neck.
| Item | Specified Condition |
| A/T | 6.5 liters (6.9 US qts, 5.7 Imp. qts) |
| M/T | 6.6 liters (7.0 US qts, 5.9 Imp. qts) |
Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant. If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Start the engine and warm it up until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
| Item | Specified Condition |
| Manual Air Conditioning System | Fan speed: Any setting except OFF Temperature: Toward WARM Air conditioning switch: OFF |
| Automatic Air Conditioning System | Temperature: Toward MAX Air conditioning switch: OFF |
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW line.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.
| 22. CHECK FOR ENGINE COOLANT LEAKS |
Remove the radiator reservoir cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Warm up the engine.
Pump the radiator cap tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leakage.
If there are no signs of external coolant leaks, check the heater core, cylinder block and head.
Reinstall the radiator reservoir cap.
| 23. INSTALL RADIATOR SUPPORT OPENING COVER |