Home › ENGINE ยท 2GR-FE › COOLING › RADIATOR

RADIATOR > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE BATTERY CLAMP SUB-ASSEMBLY


    A124917E01
  1. Remove the bolt and loosen the nut.

  1. Detach the 2 wire harness clamps.

  1. Detach the hook of the battery clamp from the front battery bracket, and then remove the battery clamp.



3. REMOVE BATTERY
  1. Remove the battery and battery insulator.



4. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 2 bolts, 4 screw, 10 clips and under cover.



5. DRAIN ENGINE COOLANT
  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator reservoir cap.

    CAUTION:
    Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



  1. Loosen the 2 cylinder block drain cock plugs.


    A126964E01



6. REMOVE V-BANK COVER SUB-ASSEMBLY


    A137900
  1. Detach the 3 clips and remove the V-bank cover.



7. REMOVE RADIATOR SUPPORT OPENING COVER


    A137899
  1. Remove the 9 clips and cover.



8. REMOVE RADIATOR GRILLE SUB-ASSEMBLY


B208461
  1. Remove the 3 bolts and 3 nuts.



    B208460
  1. Detach the 7 claws and guide, and remove the radiator grille.



9. DISCONNECT HOOD LOCK SWITCH ASSEMBLY


    A112308
  1. Disconnect the hood lock switch connector.



    A129782
  1. Disconnect the wire from the clamp.

  1. Remove the 3 bolts and disconnect the hood lock switch assembly.



10. REMOVE NO. 1 WATER BY-PASS HOSE
  1. Remove the No. 1 water by-pass hose from the radiator reservoir and No. 1 water by-pass pipe.



11. REMOVE NO. 5 WATER BY-PASS HOSE
  1. Remove the No. 5 water by-pass hose from the radiator and No. 1 water by-pass pipe.



12. REMOVE NO. 1 WATER BY-PASS PIPE
  1. Disconnect the No. 2 radiator hose from the No. 1 water by-pass pipe.



  1. Remove the 2 bolts and No. 1 water by-pass pipe.


    A112333E01



13. DISCONNECT COOLING FAN ECU HARNESS
  1. Disconnect the 2 cooling fan ECU connectors.



  1. Detach the 3 harness clamps from the fan shroud and upper radiator support.


    A136804E01



14. REMOVE UPPER RADIATOR SUPPORT BRACKET


    A112185E02
  1. Remove the 2 bolts and 2 upper radiator support brackets.



15. REMOVE NO. 2 FAN SHROUD


    A112186E01
  1. Remove the 2 bolts.

  1. Detach the 2 claws and No. 2 fan shroud.



16. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY


    A112338
  1. Remove the 4 bolts and upper radiator support sub-assembly.



17. DISCONNECT OIL COOLER INLET HOSE


18. DISCONNECT OIL COOLER OUTLET HOSE


19. DISCONNECT NO. 1 RADIATOR HOSE


20. DISCONNECT NO. 2 RADIATOR HOSE


21. REMOVE NO. 2 WATER BY-PASS HOSE


  1. Remove the No. 2 water by-pass hose from the radiator reservoir and radiator.


    A112334E01



22. REMOVE RADIATOR ASSEMBLY
  1. Detach the cooler condenser from the radiator.

    HINT:
    After detaching the condenser, make sure that all 4 fan shroud cushions are present.

  1. Remove the radiator with the 2 radiator support lower cushions.

    HINT:
    After detaching the radiator, make sure that all 2 lower radiator supports are present.

  1. Disconnect the 2 oil cooler hoses from the radiator.

  1. Remove the 2 bolts and 2 oil cooler hoses.



23. REMOVE FAN SHROUD WITH COOLING FAN


    A114328
  1. Remove the 2 bolts and fan shroud with cooling fan from the radiator.