ROOF HEADLINING (for Long Body) > INSTALLATION |
| 1. INSTALL NO. 1 ROOF SILENCER PAD |
w/o Sliding Roof:
Install the 5 silencer pads.
w/ Sliding Roof:
Install the 2 silencer pads.
| 2. INSTALL NO. 3 ROOF SILENCER PAD |
Install the No. 3 silencer pad.
| 3. INSTALL ANTENNA CORD SUB-ASSEMBLY |
for Short Body (w/o Sliding Roof):
Apply new double-sided tape as shown in the illustration.

Align the antenna cord masking tape and the edge of the roof headlining. Attach the antenna cord along the double-sided tape.
Apply tape to both ends of the antenna cord to fix the cord in place.
for Short Body (w/ Sliding Roof):
Apply new double-sided tape as shown in the illustration.

Align the antenna cord masking tape and the edge of the roof headlining. Attach the antenna cord along the double-sided tape.
Apply tape to both ends of the antenna cord to fix the cord in place.
for Long Body (w/o Sliding Roof):
Apply new double-sided tape as shown in the illustration.

Align the antenna cord masking tape and the edge of the roof headlining. Attach the antenna cord along the double-sided tape.
Apply tape to both ends of the antenna cord to fix the cord in place.
for Long Body (w/ Sliding Roof):
Apply new double-sided tape as shown in the illustration.

Align the antenna cord masking tape and the edge of the roof headlining. Attach the antenna cord along the double-sided tape.
Apply tape to both ends of the antenna cord to fix the cord in place.
| 4. INSTALL NO. 1 ROOF WIRE |
![]() |
Only when replacing the roof headlining:
Align the marking, and then install the wire harness with tape.
Attach the roof wire harness along the adhesive part.
| 5. INSTALL NO. 1 ROOF HEADLINING SUPPORT |
Install the No. 1 roof headlining support.
| 6. INSTALL NO. 2 ROOF HEADLINING SUPPORT |
Install the No. 2 roof headlining support.
| 7. INSTALL NO. 3 ROOF HEADLINING SUPPORT |
Install the No. 3 roof headlining support.
| 8. INSTALL NO. 4 ROOF HEADLINING SUPPORT |
Install the No. 4 roof headlining support.
| 9. INSTALL ROOF HEADLINING ASSEMBLY |
![]() |
w/o Sliding Roof:
Install the headlining with the 4 clips.
w/ Sliding Roof:
Install the headlining with the 2 clips.
Connect the connector to the sliding roof drive gear.
Connect the antenna cord sub-assembly.
![]() |
Install the bracket's bolt.
Attach the clamp of the antenna cord.
Connect the 2 antenna cord connectors to the rear pillar RH.
![]() |
Connect the antenna cord connector to the front pillar RH.
![]() |
Connect the No. 1 roof wire.
Connect the connector to the roof wire.
Attach the clamp of the roof wire.
| 10. INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof) |
Install the sun roof opening trim moulding.
| 11. INSTALL SHOULDER BELT ANCHOR COVER RH |
![]() |
Install the cover with the 4 claws.
| 12. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER |
![]() |
Install the cover with the 4 claws.
| 13. INSTALL REAR ASSIST GRIP ASSEMBLY |
![]() |
Attach the 4 claws to install the assist grip.
| 14. INSTALL ASSIST GRIP COVER (for Rear Grip) |
Attach the 4 claws to install the 2 assist grip covers.
| 15. INSTALL ASSIST GRIP SUB-ASSEMBLY |
![]() |
Attach the 4 claws to install the assist grip.
| 16. INSTALL ASSIST GRIP COVER (for Front Grip) |
Attach the 4 claws to install the 2 assist grip covers.
| 17. INSTALL ROOM LIGHT ASSEMBLY |
![]() |
Attach the 4 claws to install the room light switch base.
![]() |
Attach the 4 claws to install the room light.
![]() |
Install the bulb to the room light switch base.
![]() |
Attach the 4 claws and install the 2 covers.
| 18. INSTALL MAP LIGHT ASSEMBLY |
![]() |
Connect the light connector.
Attach the 4 clips to install the map light.
| 19. INSTALL VANITY LIGHT ASSEMBLY |
![]() |
Attach the 2 claws and install the vanity light lens to the vanity light.
![]() |
Install the vanity light.
| 20. INSTALL VISOR HOLDER |
![]() |
Set the claws of the visor holder as shown in the illustration.
Insert the visor holder to install it.
| 21. INSTALL VISOR ASSEMBLY LH |
![]() |
Attach the 2 claws to install the visor.
Install portion A of the visor to the visor holder.
Attach the 4 claws to install the visor bracket cover.
| 22. INSTALL VISOR ASSEMBLY RH |
| 23. INSTALL REAR ROOM PARTITION NET HOOK LH |
![]() |
Install the net hook with the 2 screws.
| 24. INSTALL REAR ROOM PARTITION NET HOOK RH |
| 25. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH |
![]() |
Attach the 7 clips to install the garnish.
| 26. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH |
| 27. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH |
![]() |
Install the belt hanger to the trim board.
Connect the power outlet socket connector.
Attach the 4 clips and 5 claws to install the trim board.
Install the 2 screws and 2 bolts.
![]() |
Connect the rear No.1 seat belt's floor anchor.
Connect the floor anchor with the bolt.
Install the anchor cover.
| 28. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH |
![]() |
Install the belt hanger to the trim board.
Attach the 4 clips and 5 claws to install the trim board.
Install the 2 screws and 2 bolts.
![]() |
Connect the rear No.1 seat belt's floor anchor.
Connect the floor anchor with the bolt.
Install the anchor cover.
| 29. INSTALL TETHER ANCHOR BRACKET SUB-ASSEMBLY |
![]() |
Install the tether anchor bracket with the bolt.
| 30. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH |
![]() |
Attach the 6 claws to install the bezel.
| 31. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL RH |
![]() |
Attach the 6 claws to install the bezel.
| 32. INSTALL REAR FLOOR FINISH PLATE |
![]() |
Attach the 2 claws and 6 clips to install the finish plate.
| 33. INSTALL BACK DOOR WEATHERSTRIP |
Install the back door weatherstrip.
| 34. INSTALL REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE |
![]() |
Attach the 7 clips to install the side plate.
Install the 4 screws.
| 35. INSTALL REAR FLOOR NO. 3 BOARD |
Install the rear floor No. 3 board.
| 36. INSTALL REAR FLOOR NO. 2 BOARD |
Install the rear floor No. 2 board.
| 37. INSTALL DECK BOARD ASSEMBLY |
Install the deck board.
| 38. INSTALL REAR FLOOR NO. 1 BOARD |
Install the rear floor No. 1 board.
| 39. INSTALL TONNEAU COVER ASSEMBLY |
Install the tonneau cover.
| 40. INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY |
Install the package tray trim pocket.
| 41. INSTALL CENTER PILLAR GARNISH LH |
![]() |
Attach the clip to install the garnish.
Install the 2 screws.
| 42. INSTALL CENTER PILLAR GARNISH RH |
| 43. INSTALL LOWER CENTER PILLAR GARNISH LH |
![]() |
Attach the 2 claws and 2 clips to install the garnish.
![]() |
Connect the front seat outer belt's floor anchor.
Connect the floor anchor with the bolt.
Install the anchor cover.
| 44. INSTALL LOWER CENTER PILLAR GARNISH RH |
| 45. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Install the rear door opening trim weatherstrip.
| 46. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
Install the rear door opening trim weatherstrip.
| 47. INSTALL REAR DOOR SCUFF PLATE LH |
![]() |
Attach the 9 claws and 2 clips to install the scuff plate.
| 48. INSTALL REAR DOOR SCUFF PLATE RH |
| 49. INSTALL UPPER INSTRUMENT PANEL |
Install the upper instrument panel (Click here).
| 50. INSTALL FRONT PILLAR GARNISH LH |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 4 wire harness clamps.
![]() |
w/ Curtain Shield Airbag:
Attach the 3 guides.
Turn the end of the front pillar garnish clip 90° with needle-nose pliers and install it to the front pillar garnish.
![]() |
Attach the 2 clips to install the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Attach the 2 clips and 3 guides to install the front pillar garnish.
| 51. INSTALL FRONT PILLAR GARNISH RH |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 4 antenna cord clamps.
![]() |
w/ Curtain Shield Airbag:
Attach the 3 guides.
Turn the end of the front pillar garnish clip 90° with needle-nose pliers and install it to the front pillar garnish.
![]() |
Attach the 2 clips to install the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Attach the 2 clips and 3 guides to install the front pillar garnish.
| 52. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Install the front door opening trim weatherstrip.
| 53. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Install the front door opening trim weatherstrip.
| 54. INSTALL COWL SIDE TRIM BOARD LH |
![]() |
Attach the 3 claws to install the trim board.
Install the cap nut.
| 55. INSTALL COWL SIDE TRIM BOARD RH |
| 56. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Attach the 10 claws to install the scuff plate.
| 57. INSTALL FRONT DOOR SCUFF PLATE RH |
| 58. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |