WIPER SWITCH > INSPECTION |
| 1. INSPECT WIPER AND WASHER SWITCH ASSEMBLY |
Check the front wiper switch.

Measure the resistance of the switch.
| Tester Connection | Switch Condition | Specified Condition |
| E13-4 (+S) - E13-2 (+1) | INT | Below 1 Ω |
| OFF | ||
| E13-3 (B) - E13-2 (+1) | MIST | |
| LO | ||
| E13-3 (B) - E13-1 (+2) | HI |
| Tester Connection | Switch Condition | Specified Condition |
| E13-1 (+S) - E13-3 (+1) | INT | Below 1 Ω |
| OFF | ||
| E13-2 (B) - E13-3 (+1) | MIST | |
| LO | ||
| E13-2 (B) - E13-4 (+2) | HI | |
| E13-9 (AUTO) - E13-10 (E)*1
| AUTO |
Check the front washer switch.
Measure the resistance of the switch.
| Tester Connection | Switch Condition | Specified Condition |
| E12-2 (EW) - E12-31 (WF) | ON | Below 1 Ω |
| OFF | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
| E12-2 (EW) - E12-3 (WF) | ON | Below 1 Ω |
| OFF | 10 kΩ or higher |
Check the intermittent operation. (LH wiper lever type)
Connect the voltmeter's positive (+) lead to terminal E13-2 (+1) and the negative (-) lead to terminal E12-2 (EW).
Connect the battery's positive (+) lead to terminal E13-2 (+B) and the negative (-) lead to terminal E12-2 (EW) and E13-4 (+S).
Turn the wiper switch to the INT position.
Connect the battery's positive (+) lead to terminal E13-4 (+S) for 5 seconds.
Connect the battery's negative (-) lead to terminal E13-4 (+S). Operate the intermittent wiper relay and check the voltage between terminals E13-2 (+1) and E12-2 (EW).

Check the intermittent operation. (RH wiper lever type)
Connect the voltmeter's positive (+) lead to terminal E13-3 (+1) and the negative (-) lead to terminal E12-2 (EW).
Connect the battery's positive (+) lead to terminal E13-2 (+B) and the negative (-) lead to terminal E12-2 (EW) and E13-1 (+S).
Turn the wiper switch to the INT position.
Connect the battery's positive (+) lead to terminal E13-1 (+S) for 5 seconds.
Connect the battery's negative (-) lead to terminal E13-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals E13-3 (+1) and E12-2 (EW).

Check the front washer operation. (LH wiper lever type)
Turn the wiper switch OFF.
Connect the battery's positive (+) lead to terminal E13-4 (+B) and the negative (-) lead to terminals E13-1 (+S) and E12-2 (EW).
Connect the voltmeter's positive (+) lead to E13-2 (+1) and the negative (-) lead to terminal E12-2 (EW).
Turn the washer switch ON and OFF, and check the voltage between terminals E13-2 (+1) and E12-2 (EW).

Check the front washer operation. (RH wiper lever type)
Turn the wiper switch OFF.
Connect the battery's positive (+) lead to terminal E13-2 (+B) and the negative (-) lead to terminals E13-4 (+S) and E12-2 (EW).
Connect the voltmeter's positive (+) lead to E13-3 (+1) and the negative (-) lead to terminal E12-2 (EW).
Turn the washer switch ON and OFF, and check the voltage between terminals E13-3 (+1) and E12-2 (EW).

Check the rear wiper switch.

Measure the resistance of the switch.
| Tester Connection | Switch Condition | Specified Condition |
| E12-2 (EW) - E12-5 (CIR) | INT | Below 1 Ω |
| E12-2 (EW) - E12-4 (+1R) | ON | |
| E12-2 (EW) - E12-5 (CIR) | OFF | 10 kΩ or higher |
| E12-2 (EW) - E12-4 (+1R) |
| Tester Connection | Switch Condition | Specified Condition |
| E12-2 (EW) - E12-6 (CIR) | INT | Below 1 Ω |
| E12-2 (EW) - E12-7 (+1R) | ON | |
| E12-2 (EW) - E12-6 (CIR) | OFF | 10 kΩ or higher |
| E12-2 (EW) - E12-7 (+1R) |
Check the rear washer switch.
Measure the resistance of the switch.
| Tester Connection | Switch Condition | Specified Condition |
| E12-2 (EW) - E12-4 (+1R) E12-2 (EW) - E13-10 (WR) | ON | Below 1 Ω |
| OFF | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
| E12-2 (EW) - E12-7 (+1R) E12-2 (EW) - E13-5 (WR) | ON | Below 1 Ω |
| OFF | 10 kΩ or higher |