LIGHTING SYSTEM > Front Fog Light Circuit |

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MAIN BODY ECU) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Select the item below in the ACTIVE TEST and then check that the relay operates.
| Item | Test Details | Diagnostic Note |
| F Fog Light Rly | Turn front fog light relay: ON / OFF | - |
|
| ||||
| NG | |
| 2.CHECK TAILLIGHT |
Check that the taillights come on when the light control switch is turned on (TAIL).
|
| ||||
| OK | |
| 3.INSPECT FUSE (FR FOG) |
Remove the FR FOG fuse from the instrument panel junction block.
Measure the resistance of the fuse.
|
| ||||
| OK | |
| 4.INSPECT FOG LIGHT BULB |
![]() |
Remove the fog light bulb.
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.
|
| ||||
| OK | |
| 5.INSPECT FRONT FOG LIGHT RELAY (Marking: FR FOG) |
![]() |
Remove the front fog light relay from the No. 6 relay block.
Measure the resistance of the relay.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (Battery voltage applied to terminals 1 and 2) |
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY) |
![]() |
Disconnect the E20 ECU connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| E20-17 (FFGO) - Body ground | Light control switch on (TAIL) | 10 to 14 V |
|
| ||||
| OK | |
| 7.CHECK WIRE HARNESS (FRONT FOG LIGHT RELAY - BATTERY) |
![]() |
Remove the front fog light relay from the No. 6 relay block.
Measure the voltage of the relay block.
| Tester Connection | Specified Condition |
| Relay block No. 6 front fog light relay terminal 5 - Body ground | 10 to 14 V |
|
| ||||
| OK | |
| 8.CHECK WIRE HARNESS (FRONT FOG LIGHT RELAY - FRONT FOG LIGHT AND BODY GROUND) |
![]() |
Remove the front fog light relay from the No. 6 relay block.
Disconnect the A15 and A42 front fog light connectors.
Measure the resistance of the wire harness side connectors and relay block.
| Tester Connection | Specified Condition |
| Relay block front fog light relay terminal 3 - A15-2 | Below 1 Ω |
| Relay block front fog light relay terminal 3 or A15-2 - Body ground | 10 kΩ or higher |
| Relay block front fog light relay terminal 3 - A42-2 | Below 1 Ω |
| Relay block front fog light relay terminal 3 or A42-2 - Body ground | 10 kΩ or higher |
| A42-1 - Body ground | Below 1 Ω |
| A15-1 - Body ground | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 9.CHECK WIRE HARNESS (DIMMER SWITCH - MAIN BODY ECU AND BODY GROUND) |

Disconnect the E15 headlight dimmer switch connector.
Disconnect the E20 main body ECU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E20-13 (FFOG) - E15-4 (BFG) | Below 1 Ω |
| E20-13 (FFOG) or E15-4 (BFG) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| E20-13 (FFOG) - E15-7 (BFG) | Below 1 Ω |
| E20-13 (FFOG) or E15-7 (BFG) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.INSPECT FOG LIGHT SWITCH |
![]() |
Remove the headlight dimmer switch.
Measure the resistance of the switch.
| Tester Connection | Condition | Specified Condition |
| 4 (BFG) - 3 (LFG) | Fog light switch OFF | 10 kΩ or higher |
| 4 (BFG) - 3 (LFG) | Fog light switch ON | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 7 (BFG) - 8 (LFG) | Fog light switch OFF | 10 kΩ or higher |
| 7 (BFG) - 8 (LFG) | Fog light switch ON | Below 1 Ω |
|
| ||||
| OK | ||
| ||