Home › TRANSMISSION ยท EB61 MANUAL TRANSAXLE › TRANSMISSION CONTROL CABLE

TRANSMISSION CONTROL CABLE > REMOVAL

for Preparation Click here



1. REMOVE NO. 2 CYLINDER HEAD COVER


    A209050
  1. Hold the rear of the cover and raise it to detach the 2 clips on the rear of the cover. Continue to raise the cover to detach the 2 clips on the front of the cover and remove the cover.

    NOTICE:
    Attempting to detach both front and rear clips at the same time may cause the cover to break.



2. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A209051
  1. Disconnect the mass air flow meter connector.

  1. Detach the clamp.



    A209053
  1. Disconnect the No. 2 ventilation hose from the cylinder head cover.

  1. Squeeze the taps of the air cleaner hose clamp, and then disconnect the air cleaner hose from the throttle body.



    A209052
  1. Detach the 2 hook clamps, and then remove the air cleaner cap and hose.



3. REMOVE AIR CLEANER CASE


    A209057
  1. Disconnect the wire harness clamp from the air cleaner case.

  1. Remove the 3 bolts and air cleaner case.



4. REMOVE NO. 1 CONSOLE UPPER PANEL GARNISH


    B208598E01
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 4 clips and remove the upper panel garnish.



5. REMOVE NO. 2 CONSOLE UPPER PANEL GARNISH


    B208599E01
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 4 clips and remove the upper panel garnish.



6. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B216883
  1. for Manual Transaxle:
    Twist the shift lever knob in the direction indicated by the arrow and remove it.



    B208597
  1. for Automatic Transaxle:
    Twist the shift lever knob in the direction indicated by the arrow and remove it.



7. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B216882
  1. Using a screwdriver, detach the 2 clips and 4 claws, and then remove the upper console panel.

    HINT:
    Tape the screwdriver tip before use.



8. REMOVE SWITCH BASE


    B209104
  1. Detach the 2 clips and 2 claws.

  1. Disconnect the connectors and remove the switch base.



9. REMOVE CONSOLE CUP HOLDER BOX


    B129881
  1. Remove the 2 screws.

  1. Detach the 2 clips and remove the cup holder box.



10. REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY


    B208374
  1. Using a screwdriver, detach the 4 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connectors and remove the upper rear console panel.



11. REMOVE CONSOLE REAR END PANEL


    B129879
  1. Using a screwdriver, detach the 6 claws and remove the console rear end panel.

    HINT:
    Tape the screwdriver tip before use.



12. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY


    B208604
  1. Remove the 2 bolts and detach the wire harness clamp.



    B208603
  1. Remove the 2 screws.

  1. Disconnect the connector and remove the rear console box.



13. DISCONNECT TRANSAXLE CONTROL CABLE ASSEMBLY


C133965
  1. Remove the 2 clips and disconnect the cable ends of the control cable.



    C133960E01
  1. Using a screwdriver, release the cable locks of the shift cable and select cable.



    C133961E01
  1. Turn the lock nuts 180° counterclockwise and hold them in that position. Remove the shift cable and select cable while holding them.

  1. Remove the shift cable from the floor shift shift lever assembly while holding the lock nut.

  1. Repeat the step above for the select cable.

    NOTICE:
    Do not push in the cable locks.



14. REMOVE TRANSAXLE CONTROL CABLE ASSEMBLY


    C202031
  1. Remove the 2 clips and disconnect the 2 cables from the transaxle.



    C202030
  1. Remove the 2 clips and disconnect the 2 cables from the control cable bracket.



    C204064
  1. Remove the 2 bolts from the retainer.

  1. Pull out the control cable from the floor.