CAN COMMUNICATION SYSTEM > CAN Main Wire for Disconnection (LHD Models) |
| Symptom | Trouble Area |
| The resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 69 Ω or more. |
|

| 1.CHECK DLC3 |
![]() |
Disconnect the E111 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E111-2 (CANH) - E16-6 (CANH) | Ignition switch off | Below 1 Ω |
| E111-13 (CANL) - E16-14 (CANL) | Ignition switch off | Below 1 Ω |
|
| ||||
| OK | |
| 2.CHECK CAN MAIN WIRE FOR DISCONNECTION (NO. 2 JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E111-3 (CANH) - E111-14 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 3.CHECK CAN MAIN WIRE FOR DISCONNECTION (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E111-1 (CANH) - E111-12 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 4.CONNECT CONNECTOR |
Reconnect the E111 No. 2 junction connector.
| NEXT | |
| 5.CHECK CAN MAIN WIRE FOR DISCONNECTION (NO. 1 JUNCTION CONNECTOR - ECM) |
![]() |
Disconnect the A80 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A80-2 (CANH) - A80-13 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 6.CHECK CAN MAIN WIRE FOR DISCONNECTION (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A80-3 (CANH) - A80-14 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 7.CONNECT CONNECTOR |
Reconnect the A80 No. 1 junction connector.
| NEXT | |
| 8.CHECK CAN MAIN WIRE FOR DISCONNECTION (ECM - NO. 1 JUNCTION CONNECTOR) |
![]() |
Disconnect the A12 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A12-8 (CANH) - A12-9 (CANL) | Ignition switch off | 108 to 132 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| A12-41 (CANH) - A12-49 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 9.CONNECT CONNECTOR |
Reconnect the E111 No. 2 junction connector.
| NEXT | |
| 10.CHECK CAN MAIN WIRE FOR DISCONNECTION (NO. 4 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
![]() |
Disconnect the E76 No. 4 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E76-4 (CANH) - E767-15 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 11.CHECK CAN MAIN WIRE FOR DISCONNECTION (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E76-5 (CANH) - E76-16 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 12.CONNECT CONNECTOR |
Reconnect the E76 No. 4 junction connector.
| NEXT | |
| 13.CHECK CAN MAIN WIRE FOR DISCONNECTION (COMBINATION METER ECU - NO. 4 JUNCTION CONNECTOR) |
![]() |
Disconnect the E22 combination meter ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E22-32 (CANH) - E22-31 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 14.CONNECT CONNECTOR |
Reconnect the E76 No. 4 junction connector.
| NEXT | |
| 15.CHECK CAN MAIN WIRE FOR DISCONNECTION (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
![]() |
Disconnect the E115 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E115-3 (CANH) - E115-14 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 16.CHECK CAN MAIN WIRE FOR DISCONNECTION (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E115-2 (CANH) - E115-13 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||