Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder

for Preparation Click here


DESCRIPTION

The main body ECU receives switch signals from the door control switch on the power window regulator master switch, door control switch, driver side door key cylinder, passenger side door key cylinder and passenger side door lock switch, and activates the door lock motor on each door accordingly.

WIRING DIAGRAM


E123922E02


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR LOCK)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the doors lock / unlock.

    Main body ECU 
    Item
    Test Details
    Diagnostic Note
    DOOR LOCK
    Operate door lock motor
    LOCK / UNLOCK
    -

    OK:
    Doors can lock / unlock.



OK
Go to step 4
NG


2.INSPECT FUSE (ECU - B)
  1. Remove the ECU-B fuse from the engine room No. 2 relay block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


3.CHECK WIRE HARNESS (ECU - BATTERY AND BODY GROUND)

E123923E02

  1. Disconnect the IB and IE junction block connectors.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    IB-30 (BECU) - Body ground
    10 to 14 V

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    IE-17 (GND1) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) 

4.CHECK DRIVER SIDE DOOR LOCK / UNLOCK OPERATION
  1. Proceed to the next step according to the symptom listed in the table below.

    Symptom
    Proceed to
    All doors cannot be locked / unlocked at once using door control switch on power window regulator master switch.
    A
    All doors cannot be locked / unlocked at once using door key cylinder on driver side.
    B
    All doors cannot be locked / unlocked at once using both door control switch on master switch and door key cylinder on driver side.
    C



B
Go to step 8

C
REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
A


5.READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH ON MASTER SWITCH)
  1. Use the Data List to check if the door control switch is functioning properly.

    Main body ECU 
    Item
    Measurement / Display (Range)
    Normal Condition
    Diagnostic Note
    Door Lock SW-Lock
    Door manual lock switch signal / ON or OFF
    ON: Door control switch on power window regulator master switch is pushed to lock position
    OFF: Door control switch on power window regulator master switch is pushed
    -
    Door Lock SW-Unlock
    Door manual unlock switch signal / ON or OFF
    ON: Door control switch on power window regulator master switch is pushed to unlock position
    OFF: Door control switch on power window regulator master switch is pushed
    -

    OK:
    When the switch is operating, the intelligent tester should display as shown in the table.



OK
REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
NG


6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    E123893E01
  1. Remove the master switch.

  1. Measure the resistance of the door control switch.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (L) - 1 (E)
    Lock
    Below 80 Ω
    2 (L) - 1 (E)
    OFF
    10 kΩ or higher
    9 (UL) - 1 (E)
    Unlock
    Below 80 Ω
    9 (UL) - 1 (E)
    OFF
    10 kΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (L) - 9 (E)
    Lock
    Below 80 Ω
    2 (L) - 9 (E)
    OFF
    10 kΩ or higher
    8 (UL) - 9 (E)
    Unlock
    Below 80 Ω
    8 (UL) - 9 (E)
    OFF
    10 kΩ or higher



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


7.CHECK WIRE HARNESS (MASTER SWITCH - ECU AND BODY GROUND)

E123929E02

  1. for LHD:

    1. Disconnect the H2 master switch connector.

    2. Disconnect the IH junction block connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      H2-2 (L) - IH-4 (L1)
      Below 1 Ω
      H2-2 (L) - Body ground
      10 kΩ or higher
      IH-4 (L1) - Body ground
      10 kΩ or higher
      H2-9 (UL) - IH-5 (UL1)
      Below 1 Ω
      H2-9 (UL) - Body ground
      10 kΩ or higher
      IH-5 (UL1) - Body ground
      10 kΩ or higher
      H2-1 (E) - Body ground
      Below 1 Ω

  1. for RHD:

    1. Disconnect the G8 master switch connector.

    2. Disconnect the IH junction block connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      G8-2 (L) - IH-13 (L1)
      Below 1 Ω
      G8-2 (L) - Body ground
      10 kΩ or higher
      IH-13 (L1) - Body ground
      10 kΩ or higher
      G8-8 (UL) - IH-14 (UL1)
      Below 1 Ω
      G8-8 (UL) - Body ground
      10 kΩ or higher
      IH-14 (UL1) - Body ground
      10 kΩ or higher
      G8-9 (E) - Body ground
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) 

8.READ VALUE USING INTELLIGENT TESTER (DOOR KEY SWITCH)
  1. Use the Data List to check if the door key is functioning properly.

    Main body ECU 
    Item
    Measurement / Display (Range)
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Door key linked lock switch signal / ON or OFF
    ON: Driver side door key cylinder is turned to lock position
    OFF: Driver side door key cylinder is not turned
    -
    Door Key SW-Unlock
    Door key linked lock switch signal / ON or OFF
    ON: Driver side door key cylinder is turned to unlock position
    OFF: Driver side door key cylinder is not turned
    -

    OK:
    When the door key is operating, the intelligent tester should display as shown in the table.



OK
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
NG


9.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY (DRIVER SIDE)


    B112017E03
  1. for LHD:

    1. Remove the front door lock.

    2. Measure the resistance of the door lock and unlock switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      9 (L) -7 (E)
      Lock
      Below 1 Ω
      9 (L) -7 (E)
      OFF
      10 kΩ or higher
      10 (UL) - 7 (E)
      Unlock
      Below 1 Ω
      10 (UL) - 7 (E)
      OFF
      10 kΩ or higher



    B117135E02
  1. for RHD (w/o Double Locking System):

    1. Remove the front door lock.

    2. Measure the resistance of the door key lock and unlock switch operation.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      5 (UL) -8 (E)
      Lock
      Below 1 Ω
      5 (UL) -8 (E)
      OFF
      10 kΩ or higher
      6 (L) - 8 (E)
      Unlock
      Below 1 Ω
      6 (L) - 8 (E)
      OFF
      10 kΩ or higher



    E123940E01
  1. for RHD (w/ Double Locking System):

    1. Remove the front door lock.

    2. Measure the resistance of the door lock and unlock switch.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      5 (UL) -8 (E)
      Lock
      Below 1 Ω
      5 (UL) -8 (E)
      OFF
      10 kΩ or higher
      6 (L) - 8 (E)
      Unlock
      Below 1 Ω
      6 (L) - 8 (E)
      OFF
      10 kΩ or higher



NG
REPLACE FRONT DOOR WITH MOTOR LOCK ASSEMBLY (DRIVER SIDE)
OK


10.CHECK WIRE HARNESS (MOTOR - ECU AND BODY GROUND)

E123924E03

  1. for LHD:

    1. Disconnect the H5 door lock motor connector.

    2. Disconnect the IH junction block connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      H5-9 (L) - IH-7 (L2)
      Below 1 Ω
      H5-9 (L) - Body ground
      10 kΩ or higher
      IH-7 (L2) - Body ground
      10 kΩ or higher
      H5-10 (UL) - IH-6 (UL2)
      Below 1 Ω
      H5-10 (UL) - Body ground
      10 kΩ or higher
      IH-6 (UL2) - Body ground
      10 kΩ or higher

  1. for RHD:

    1. Disconnect the G5 door lock motor connector.

    2. Disconnect the IH junction block connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      G5-6 (L) - IH-16 (L2)
      Below 1 Ω
      G5-6 (L) - Body ground
      10 kΩ or higher
      IH-16 (L2) - Body ground
      10 kΩ or higher
      G5-5 (UL) - IH-15 (UL2)
      Below 1 Ω
      G5-5 (UL) - Body ground
      10 kΩ or higher
      IH-15 (UL2) - Body ground
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)