Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (w/ Navigation System)

REAR VIEW MONITOR SYSTEM (w/ Navigation System) > TERMINALS OF ECU

for Preparation Click here



CHECK NAVIGATION RECEIVER ASSEMBLY (for HDD Navigation System)

E178165E03

  1. Disconnect the E52 navigation receiver assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E52-7 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    E52-3 (ACC) - E52-7 (GND)
    GR - BR
    Accessory (On)
    Ignition switch off
    Below 1 V
    Ignition switch ACC
    11 to 14 V
    E52-4 (B) - E52-7 (GND)
    L - BR
    Battery
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E52 navigation receiver assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E106-2 (CA+) - E106-12 (CGND)
    B - Shielded
    Power source
    Ignition switch ON, shift lever in R
    5.8 to 6.2 V
    E106-12 (CGND) - Body ground
    Shielded - Body ground
    Shielding
    Always
    Below 1 V
    E57-4 (BTCY) - Body ground
    LG - Body ground
    Back door courtesy light switch signal
    Back door open
    Below 1 V
    Back door closed
    11 to 14 V
    E57-5 (REV) - E52-7 (GND)
    R - BR
    Reverse signal
    Ignition switch ON, shift lever in R
    11 to 14 V
    Ignition switch ON, shift lever not in R
    Below 1 V
    E106-1 (V+) - E106-11 (V-)
    W - R
    Display signal
    Ignition switch ON, shift lever in R
    Waveform 1
    Ignition switch ON, shift lever in R, screen blacked out by covering camera lens
    Waveform 2
    If the result is not as specified, the navigation receiver assembly may have a malfunction.



  5. E159949E01
  6. Using an oscilloscope, check waveform 1.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    E106-1 (V+) - E106-11 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    Ignition switch ON, shift lever in R



  7. E164781E01
  8. Using an oscilloscope, check waveform 2.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    E106-1 (V+) - E106-11 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    Ignition switch ON, shift lever in R, screen blacked out by covering camera lens


CHECK NAVIGATION RECEIVER ASSEMBLY (for DVD Navigation System with 3ZR-FAE)

E178163E03

  1. Disconnect the E52 navigation receiver assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E52-7 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    E52-3 (ACC) - E52-7 (GND)
    GR - BR
    Accessory (On)
    Ignition switch off
    Below 1 V
    Ignition switch ACC
    11 to 14 V
    E52-4 (B) - E52-7 (GND)
    L - BR
    Battery
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E52 navigation receiver assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E106-2 (CA+) - E106-12 (CGND)
    B - Shielded
    Power source
    Ignition switch ON, shift lever in R
    5.8 to 6.2 V
    E106-12 (CGND) - Body ground
    Shielded - Body ground
    Shielding
    Always
    Below 1 V
    E57-4 (BTCY) - Body ground
    LG - Body ground
    Back door courtesy light switch signal
    Back door open
    Below 1 V
    Back door closed
    11 to 14 V
    E57-5 (REV) - E52-7 (GND)
    R - BR
    Reverse signal
    Ignition switch ON, shift lever in R
    11 to 14 V
    Ignition switch ON, shift lever not in R
    Below 1 V
    E106-1 (V+) - E106-11 (V-)
    W - R
    Display signal
    Ignition switch ON, shift lever in R
    Waveform 1
    Ignition switch ON, shift lever in R, screen blacked out by covering camera lens
    Waveform 2
    If the result is not as specified, the navigation receiver assembly may have a malfunction.



  5. E159949E01
  6. Using an oscilloscope, check waveform 1.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    E106-1 (V+) - E106-11 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    Ignition switch ON, shift lever in R



  7. E164781E01
  8. Using an oscilloscope, check waveform 2.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    E106-1 (V+) - E106-11 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    Ignition switch ON, shift lever in R, screen blacked out by covering camera lens


CHECK NAVIGATION RECEIVER ASSEMBLY (for DVD Navigation System except 3ZR-FAE) (Click here)