DTC B2326 CAN MS Bus Line Communication Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B2326 | Lost Communication with the main body ECU. |
|


| 1.CHECK CAN BUS LINE (MAIN WIRE FOR DISCONNECTION, BUS LINES FOR SHORT CIRCUIT) |
Remove the main body ECU with the connector connected.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Resistance of Malfunction |
| E19-11 (CANP) - E19-12 (CANN) | Ignition switch off | 54 to 69 Ω | Below 53 Ω: Short in line |
| E19-11 (CANP) - E19-12 (CANN) | Ignition switch off | 54 to 69 Ω | Higher than 69 Ω or higher: Open in CAN main bus line |
| E19-11 (CANP) - IE-17 (GND1) | Ignition switch off | 200 Ω or higher | Below 200 Ω: Ground short |
| E19-12 (CANN) - IE-17 (GND1) | Ignition switch off | 200 Ω or higher | Below 200 Ω: Ground short |
| E19-11 (CANP) - E19-1 (AM1) | Ignition switch off | 6 kΩ or higher | Below 6 kΩ: +B short |
| E19-12 (CANN) - E19-1 (AM1) | Ignition switch off | 6 kΩ or higher | Below 6 kΩ: +B short |
| Result | Proceed to |
NG
| A |
NG
| B |
| OK | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK CAN MAIN WIRE FOR DISCONNECTION (NO. 4 JUNCTION CONNECTOR) |
for LHD
![]() |
Disconnect the E76 No. 4 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Inspection Area |
| E76-9 (MSCH) - E76-20 (MSCL) | Ignition switch off | 108 to 132 Ω | Combination meter side CAN main wire |
| E76-11 (CANP) - E76- 22 (CANN) | Ignition switch off | 108 to 132 Ω | Main body ECU side CAN main wire |
![]() |
for RHD
Disconnect the E113 and E114 No. 4 junction connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Inspection Area |
| E113-1 (MSCH) - E113-12 (MSCL) | Ignition switch off | 108 to 132 Ω | Combination meter side CAN main wire |
| E114-11 (CANP) - E114-22 (CANN) | Ignition switch off | 108 to 132 Ω | Main body ECU side CAN main wire |
| Result | Proceed to |
| NG (Combination meter side CAN main wire) | A |
| NG (Main body ECU side CAN main wire) | B |
| OK | C |
|
| ||||
|
| ||||
| A | |
| 3.CONNECT CONNECTOR |
Reconnect the E76*1 or E113*2 and E114*2 No. 4 junction connectors.
| NEXT | |
| 4.CHECK CAN MAIN WIRE FOR DISCONNECTION (COMBINATION METER ECU) |
![]() |
Disconnect the E22 combination meter ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E22-9 (MSCH) - E22-10 (MSCL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 5.CONNECT CONNECTOR |
Reconnect the E76*1 or E113*2 and E114*2 No. 4 junction connectors.
| NEXT | |
| 6.CHECK CAN MAIN WIRE FOR DISCONNECTION (MAIN BODY ECU) |
![]() |
Disconnect the E19 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-11 (CANP) - E19-12 (CANN) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 7.CHECK CAN BUS LINE FOR SHORT |
Remove the main body ECU with the connector connected.

Disconnect the E22 combination meter ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-11 (CANP) - E19-12 (CANN) | Ignition switch off | 108 to 132 Ω |
| E19-11 (CANP) - IE-17 (GND1) | Ignition switch off | 200 Ω or higher |
| E19-12 (CANN) - IE-17 (GND1) | Ignition switch off | 200 Ω or higher |
| E19-11 (CANP) - E19-1 (AM1) | Ignition switch off | 6 kΩ or higher |
| E19-12 (CANN) - E19-1 (AM1) | Ignition switch off | 6 kΩ or higher |
Reconnect the E22 combination meter ECU connector.
Disconnect the E63 certification ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-11 (CANP) - E19-12 (CANN) | Ignition switch off | 54 to 69 Ω |
| E19-11 (CANP) - IE-17 (GND1) | Ignition switch off | 200 Ω or higher |
| E19-12 (CANN) - IE-17 (GND1) | Ignition switch off | 200 Ω or higher |
| E19-11 (CANP) - E19-1 (AM1) | Ignition switch off | 6 kΩ or higher |
| E19-12 (CANN) - E19-1 (AM1) | Ignition switch off | 6 kΩ or higher |
Reconnect the E63 certification ECU connector.
| Result | Proceed to |
| NG | A |
| OK (Combination meter ECU) | B |
| OK (Certification ECU) | C |
|
| ||||
|
| ||||
| A | |
| 8.CHECK CAN BUS LINE FOR SHORT (MAIN BODY ECU) |
Disconnect the E76*1 or E114*2 No. 4 junction connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-11 (CANP) - E19-12 (CANN) | Ignition switch off | 108 to 132 Ω |
| E19-11 (CANP) - IE-17 (GND1) | Ignition switch off | 200 Ω or higher |
| E19-12 (CANN) - IE-17 (GND1) | Ignition switch off | 200 Ω or higher |
| E19-11 (CANP) - E19-1 (AM1) | Ignition switch off | 6 kΩ or higher |
| E19-12 (CANN) - E19-1 (AM1) | Ignition switch off | 6 kΩ or higher |
|
| ||||
| OK | |
| 9.CHECK CAN BUS LINE FOR SHORT (COMBINATION METER ECU) |
![]() |
Disconnect the E22 combination meter ECU connector.
Disconnect the E76*1 or E113*2 No. 4 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E22-9 (MSCH) - E22-10 (MSCL) | Ignition switch off | 200 Ω or higher |
| E22-9 (MSCH) - E22-33 (ET) | Ignition switch off | 200 Ω or higher |
| E22-10 (MSCL) - E22-33 (ET) | Ignition switch off | 200 Ω or higher |
| E22-9 (MSCH) - E22-22 (B) | Ignition switch off | 6 kΩ or higher |
| E22-10 (MSCL) - E22-22 (B) | Ignition switch off | 6 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK CAN BUS LINE FOR SHORT (CERTIFICATION ECU) |
![]() |
Disconnect the E63 certification ECU connector.
Disconnect the E76*1 or E113*2 No. 4 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E63-27 (CANH) - E63-28 (CANL) | Ignition switch off | 200 Ω or higher |
| E63-27 (CANH) - E63-17 (E) | Ignition switch off | 200 Ω or higher |
| E63-28 (CANL) - E63-17 (E) | Ignition switch off | 200 Ω or higher |
| E63-27 (CANH) - E63-1 (+B) | Ignition switch off | 6 kΩ or higher |
| E63-28 (CANL) - E63-1 (+B) | Ignition switch off | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 11.CHECK CAN BUS LINE FOR SHORT |
![]() |
Disconnect the E19 and IE main body ECU connectors.
Disconnect the E76*1 or E114*2 No. 4 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E19-11 (CANP) - E19-12 (CANN) | Ignition switch off | 200 Ω or higher |
| E19-11 (CANP) - IE-17 (GND1) | Ignition switch off | 200 Ω or higher |
| E19-12 (CANN) - IE-17 (GND1) | Ignition switch off | 200 Ω or higher |
| E19-11 (CANP) - E19-1 (AM1) | Ignition switch off | 6 kΩ or higher |
| E19-12 (CANN) - E19-1 (AM1) | Ignition switch off | 6 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 12.CHECK CAN BUS LINE FOR DISCONNECTION |
Recheck for DTC.
| NEXT | ||
| ||