Home › TRANSMISSION ยท E352 MANUAL TRANSAXLE › MANUAL TRANSAXLE UNIT

MANUAL TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY


C069774E01
  1. Remove the clutch release fork with the clutch release bearing from the transaxle case.



2. REMOVE CLUTCH RELEASE BEARING ASSEMBLY
  1. Remove the release bearing and clutch release bearing hub clip from the clutch release fork.



3. REMOVE CLUTCH RELEASE FORK SUPPORT


C083809E01
  1. Remove the clutch release fork support from the transaxle case.



4. REMOVE CLUTCH RELEASE FORK BOOT
  1. Remove the clutch release fork boot from the transaxle case.



5. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Remove the bolt and hole cover.

  1. Remove the O-ring from the hole cover.



6. REMOVE SELECTING BELLCRANK ASSEMBLY


C092831E01
  1. Remove the 2 bolts and selecting bellcrank from the transaxle case.

  1. Remove the shift and select lever bush from the selecting bellcrank.



7. REMOVE CONTROL SHIFT LEVER


C092832E01
  1. Remove the nut and spring washer.



    C092833E01
  1. Using a brass bar and hammer, tap out the shift outer lever lever lock pin.

  1. Remove the control shift lever.



8. REMOVE CONTROL SHAFT COVER


C092834E01
  1. Remove the 4 bolts, control shift cover and gasket from the transaxle case.



9. FIX MANUAL TRANSAXLE ASSEMBLY


C087963E02
  1. Place the transaxle on wooden blocks.



10. REMOVE NO. 1 LOCK BALL ASSEMBLY


C087964E01
  1. Remove the lock ball from the transaxle case.



11. REMOVE MANUAL TRANSAXLE BREATHER PLUG


C087965E02
  1. Remove the breather plug and gasket.



12. REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY


C138371
  1. Remove the shift and select lever shaft from the transaxle case.



13. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY


C087966E02
  1. Remove the back-up light switch and gasket from the transaxle case.



14. REMOVE FILLER PLUG


C070824E02
  1. Remove the filler plug and gasket from the transaxle case.



15. REMOVE DRAIN PLUG SUB-ASSEMBLY


C087967E02
  1. Remove the drain plug and gasket from the transaxle case.



16. REMOVE MANUAL TRANSAXLE CASE COVER SUB-ASSEMBLY


C083219E01
  1. Remove the 10 bolts and transaxle case cover from the transaxle case.



17. REMOVE REAR MANUAL TRANSAXLE OUTPUT SHAFT SET NUT


C069266E01
  1. Engage the 2 gears simultaneously to lock the transaxle.



    C087968E01
  1. Using SST and a hammer, unstake the rear set nut.

    SST
    09930-00010  



    C087969E01
  1. Using SST, remove the shaft rear set nut from the output shaft.

    SST
    09229-55010  

  1. Disengage the 2 gears.



18. INSPECT 5TH GEAR THRUST CLEARANCE


C069517E01
  1. Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.65 mm (0.0039 to 0.0256 in.)

    If the clearance is out of the specification, replace the No. 3 transaxle clutch hub, 5th gear or input shaft rear radial ball bearing.



19. INSPECT 5TH GEAR RADIAL CLEARANCE


C069516E01
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.009 to 0.050 mm (0.0004 to 0.0020 in.)

    If the clearance is out of the specification, replace the 5th gear, 5th gear needle roller bearing or input shaft.



20. REMOVE NO. 3 TRANSAXLE CLUTCH HUB


C069269E01
  1. Using 2 screwdrivers and a hammer, tap out the No. 3 transaxle clutch hub shaft snap ring from the input shaft.

    HINT:
    Cover with a shop rag to keep the snap ring from flying off.



    C069270E01
  1. Remove the shift fork set bolt from the No. 3 gear shift fork.



    C069777E02
  1. Using SST, remove the No. 3 transaxle clutch hub, No. 3 transaxle hub sleeve and No. 3 gear shift fork from the input shaft.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010)
    09950-50013   (09957-04010)
    09950-60010   (09951-00280)



21. REMOVE 5TH GEAR


C069454E01
  1. Remove the 5th gear from the input shaft.



22. REMOVE 5TH GEAR NEEDLE ROLLER BEARING


C069455E01
  1. Remove the needle roller bearing from the input shaft.



23. REMOVE 5TH DRIVEN GEAR


C069456E01
  1. Using SST, remove the 5th driven gear from the output shaft.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09957-04010)
    09950-60010   (09951-00180, 09955-03011)
    09950-50013  



24. REMOVE REAR BEARING RETAINER


C069457E01
  1. Using a T45 "torx" socket, remove the 7 "torx" screws and bearing retainer from the transaxle case.



25. REMOVE OUTPUT SHAFT REAR BEARING SHIM


C069458E01
  1. Remove the rear bearing shim from the output shaft.



26. REMOVE INPUT SHAFT REAR BEARING SHAFT SNAP RING


C087970E01
  1. Using a snap ring expander, remove the shaft snap ring from the input shaft.



27. REMOVE SHIFT FORK SHAFT SHAFT SNAP RING


C087971E01
  1. Using 2 screwdrivers and a hammer, tap out the shaft snap ring from the No. 1 gear shift fork shaft.

    HINT:
    Cover with a shop rag to keep the snap ring from flying off.



    C069460E01
  1. Using 2 screwdrivers and a hammer, tap out the shaft snap ring from the No. 2 gear shift fork shaft.

    HINT:
    Cover with a shop rag to keep the snap ring from flying off.



28. REMOVE REVERSE IDLER GEAR SHAFT BOLT


C083225E01
  1. Remove the reverse idler gear shaft bolt and gasket.



29. REMOVE CLUTCH TUBE BRACKET
  1. Remove the bolt and clutch tube bracket.



30. REMOVE MANUAL TRANSAXLE CASE


C083226E01
  1. Remove the 3 bolts from the transaxle case side.



    C083227E01
  1. Remove the 14 bolts from the transaxle case side.

  1. Remove the transaxle case by tapping it using a plastic-faced hammer.



31. REMOVE NO. 2 OIL RECEIVER PIPE


C138376
  1. Remove the bolt and oil receiver pipe from the transaxle case.

    NOTICE:
    Do not damage the pipe.



32. REMOVE NO. 1 OIL RECEIVER PIPE


C138375
  1. Remove the bolt and oil receiver pipe from the transaxle case.

    NOTICE:
    Do not damage the pipe.



33. REMOVE REVERSE RESTRICT PIN ASSEMBLY


C070521E01
  1. Using a 6 mm hexagon wrench, remove the restrict pin plug from the transaxle case.



    C069467E01
  1. Using a 5 mm pin punch and hammer, tap out the slotted pin.



    C135411
  1. Remove the bolt, transmission oil baffle and reverse restrict pin.



34. REMOVE TRANSAXLE MAGNET


C069468E01
  1. Remove the magnet from the transaxle case.



35. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY


C069470E01
  1. Remove the reverse idler gear with the reverse idler gear shaft from the transaxle case.



    C070512E01
  1. Remove the reverse idler gear and reverse idler thrust washer from the gear shaft.



36. REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY


C083230E01
  1. Remove the 2 bolts and arm bracket from the transaxle case.



37. REMOVE NO. 1 GEAR SHIFT FORK SHAFT


C083231E01
  1. Remove the shift fork set bolt from the No. 1 gear shift fork.



    C087975E01
  1. Pull out the No. 1 gear shift fork shaft while the No. 3 gear shift fork shift is pulled up.



    C069500E01
  1. Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring from the No. 1 gear shift fork shaft.

    HINT:
    Cover with a shop rag to keep the snap ring from flying off.



38. REMOVE REVERSE SHIFT FORK ROLLER


C083233E01
  1. Using a magnetic finger, remove the reverse shift fork roller from the reverse shift fork.



39. REMOVE NO. 2 GEAR SHIFT FORK SHAFT


C083234E01
  1. Remove the shift fork set bolt and shift head set bolt from the No. 2 gear shift fork and No. 1 gear shift head.



    C087976E05
  1. Remove the No. 2 gear shift fork shaft head and No. 1 gear shift head from the transaxle case.



40. REMOVE NO. 1 GEAR SHIFT FORK


C087977E01


41. REMOVE NO. 3 GEAR SHIFT FORK SHAFT


C087978E04
  1. Remove the No. 3 gear shift fork shaft from the transaxle case.



    C083238E01
  1. Using 2 screwdrivers and a hammer, tap out the 2 shift fork shaft snap rings from the No. 3 gear shift fork shaft.

    HINT:
    Cover with a shop rag to keep the snap ring from flying off.

  1. Remove the reverse shift fork from the No. 3 gear shift fork shaft.



42. REMOVE NO. 2 GEAR SHIFT FORK


C087979E03
  1. Remove the No. 2 gear shift fork from the input shaft.



43. REMOVE INPUT SHAFT ASSEMBLY


C083240E01
  1. Tilt the output shaft, then remove the input shaft from the transaxle case.



44. REMOVE OUTPUT SHAFT ASSEMBLY


C083241E01
  1. Slightly lift up on the differential case with the output shaft at an angle.

  1. Remove the output shaft from the transaxle case.



45. REMOVE DIFFERENTIAL CASE ASSEMBLY


C083242E01
  1. Remove the differential case from the transaxle case.



46. REMOVE MANUAL TRANSAXLE CASE RECEIVER


C083243E01
  1. Remove the 3 bolts and receiver from the transaxle case.



47. REMOVE INPUT SHAFT FRONT BEARING


C087980E01
  1. Using SST, remove the input shaft front bearing (outer race) from the transaxle case.

    SST
    09612-65014   (09612-01040, 09612-01050)



48. REMOVE FRONT TRANSAXLE CASE OIL SEAL


C087981E01
  1. Using SST, remove the oil seal from the transaxle case.

    SST
    09612-65014   (09612-01040, 09612-01050)



49. REMOVE FRONT OUTPUT SHAFT BEARING


C087982E01
  1. Using SST, remove the front bearing (outer race) from the transaxle case.

    SST
    09387-00041   (09387-02020, 09387-02010)



50. REMOVE OUTPUT SHAFT COVER


C069483E01
  1. Remove the output shaft cover from the transaxle case.



51. REMOVE REAR OUTPUT SHAFT BEARING


C087983E01
  1. Using SST, tap out the rear bearing from the transaxle case (outer race).

    SST
    09950-60010   (09951-00680)
    09950-70010   (09951-07100)



52. REMOVE TRANSAXLE CASE OIL SEAL


C087984E01
  1. Using SST, tap out the oil seal from the transaxle case.

    SST
    09308-00010  



53. REMOVE FRONT TRANSAXLE CASE COVER OIL SEAL


D032768E01
  1. Using a screwdriver, pry out the cover oil seal.

    HINT:
    Tape the screwdriver tip before use to avoid damage.



54. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


C069490E01
  1. Using a brass bar and hammer, tap out the front tapered roller bearing (outer race) from the transaxle case.



    C070822E01
  1. Using SST, remove the case front tapered roller bearing from the front differential case.

    SST
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)
    09950-60010   (09951-00560)



55. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


C087986E01
  1. Using SST and a hammer, tap out the rear tapered roller bearing (outer race) and rear shim from the transaxle case.

    SST
    09950-60020   (09951-00790)
    09950-70010   (09951-07100)



    C090344E01
  1. Using SST, remove the rear tapered roller bearing (inner race) from the front differential case.

    SST
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)
    09950-60010   (09951-00490)



56. REMOVE NO. 3 TRANSAXLE HUB SLEEVE


C087988E01
  1. Remove the No. 3 transaxle hub sleeve from the No. 3 transaxle clutch hub.



57. REMOVE NO. 3 SYNCHROMESH SHIFTING KEY SPRING


C069507E01
  1. Remove the 2 No. 3 synchromesh shifting key springs and synchronizer ring set from the No. 3 transaxle clutch hub while pushing on the No. 3 synchromesh shifting key spring.



58. REMOVE SYNCHRONIZER PULL RING


C069508E01
  1. Using a screwdriver, remove the synchronizer pull ring snap ring.

  1. Remove the synchronizer pull ring, No. 5 synchronizer ring outer, No. 5 synchronizer ring inner and No. 5 synchronizer ring middle.