Home › TRANSMISSION ยท E352F / E359F MANUAL TRANSAXLE › OUTPUT SHAFT

OUTPUT SHAFT > REASSEMBLY

for Preparation Click here



1. INSTALL REVERSE GEAR


C069672E01
  1. Coat the reverse gear with gear oil.

  1. Install the 3 No. 1 synchromesh shifting key springs and No. 1 transaxle clutch hub to the reverse gear.

    NOTICE:
    Assemble the reverse gear and the No. 1 transaxle clutch hub in the correct direction.

  1. Using a screwdriver, install the 3 No. 1 synchromesh shifting keys to the reverse gear.



2. INSTALL FRONT OUTPUT SHAFT BEARING


C092874E01
  1. Using SST and a press, press in the front bearing (inner race) to the output shaft.

    SST
    09950-60010   (09951-00430)
    09950-70010   (09951-07150)



3. INSTALL NO. 1 SYNCHRONIZER RING SET


C069649E02
  1. Coat the No. 1 synchronizer ring set with gear oil, and install it to the 1st gear.

    NOTICE:
    Align the claw of the No. 1 synchronizer ring set (middle) with the hole of the 1st gear and install it.



4. INSTALL 1ST GEAR NEEDLE ROLLER BEARING


C069650E02
  1. Coat the needle roller bearing with gear oil, and install it to the output shaft.



5. INSTALL 1ST GEAR


C069673E02
  1. Coat the 1st gear with gear oil, and install it to the output shaft.



6. INSTALL NO. 1 TRANSAXLE CLUTCH HUB


C092862E01
  1. Using SST and a press, press in the No. 1 transaxle clutch hub to the output shaft.

    SST
    09316-60011   (09316-00031)
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    1. Align the claw of the No. 1 synchronizer ring set (outer) with the hole of the No. 1 transaxle clutch hub and install it.
    2. Make sure that the 1st gear rotates.



7. INSTALL 2ND GEAR BUSH BALL


C083814E02
  1. Coat the bush ball with MP grease, and install it to the output shaft.



8. INSTALL 2ND GEAR BUSH


C069646E02
  1. Coat the bush with gear oil, and install it to the output shaft.



9. INSTALL 2ND GEAR BEARING SPACER


C069645E02
  1. Coat the bearing spacer with gear oil, and install it to the output shaft.



10. INSTALL 2ND GEAR NEEDLE ROLLER BEARING


C069644E02
  1. Coat the needle roller bearing with gear oil, and install it to the output shaft.



11. INSTALL NO. 2 SYNCHRONIZER RING SET


C069643E02
  1. Coat the No. 2 synchronizer ring set with gear oil, and install it to the No. 1 transaxle clutch hub.

    NOTICE:
    Align the key groove on the No. 2 synchronizer ring set with the No. 1 synchromesh shifting key.



12. INSTALL 2ND GEAR


C069679E01
  1. Coat the 2nd gear with gear oil, and install it to the output shaft.



13. INSTALL 3RD DRIVEN GEAR


C092863E01
  1. Using SST and a press, press in the 3rd driven gear to the output shaft.

    SST
    09608-00071  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)



14. INSTALL OUTPUT GEAR SPACER


C069641E02
  1. Install the output gear spacer to the output shaft.



15. INSTALL 4TH DRIVEN GEAR


C092864E01
  1. Using SST and a press, press in the 4th driven gear to the output shaft.

    SST
    09608-00071  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)



16. INSTALL FRONT OUTPUT SHAFT BEARING


C092865E01
  1. Using SST and a press, press in the front bearing (inner race) to the output shaft.

    SST
    09506-30012  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)



17. INSPECT 2ND GEAR RADIAL CLEARANCE


C069639E02
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    Bearing
    Specified Condition
    KOYO made
    0.009 to 0.053 mm (0.0004 to 0.0021 in.)
    NSK made
    0.009 to 0.051 mm (0.0004 to 0.0020 in.)

    If the clearance is out of the specification, replace the 2nd gear, 2nd gear bush and 2nd gear needle roller bearing.



18. INSPECT 1ST GEAR RADIAL CLEARANCE


C069638E02
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    Bearing
    Specified Condition
    KOYO made
    0.009 to 0.053 mm (0.0004 to 0.0021 in.)
    NSK made
    0.009 to 0.051 mm (0.0004 to 0.0020 in.)

    If the clearance is out of the specification, replace the 1st gear and 1st gear needle roller bearing.



19. INSPECT 2ND GEAR THRUST CLEARANCE


C069637E03
  1. Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)

    If the clearance is out of the specification, replace the No. 1 transaxle clutch hub, 2nd gear or 3rd driven gear.



20. INSPECT 1ST GEAR THRUST CLEARANCE


C068252E02
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.25 to 0.40 mm (0.0098 to 0.0157 in.)

    If the clearance is out of the specification, replace the 1st gear or No. 1 transaxle clutch hub.