OUTPUT SHAFT > REASSEMBLY |
| 1. INSTALL REVERSE GEAR |
![]() |
Coat the reverse gear with gear oil.
Install the 3 No. 1 synchromesh shifting key springs and No. 1 transaxle clutch hub to the reverse gear.
Using a screwdriver, install the 3 No. 1 synchromesh shifting keys to the reverse gear.
| 2. INSTALL FRONT OUTPUT SHAFT BEARING |
![]() |
Using SST and a press, press in the front bearing (inner race) to the output shaft.
| 3. INSTALL NO. 1 SYNCHRONIZER RING SET |
![]() |
Coat the No. 1 synchronizer ring set with gear oil, and install it to the 1st gear.
| 4. INSTALL 1ST GEAR NEEDLE ROLLER BEARING |
![]() |
Coat the needle roller bearing with gear oil, and install it to the output shaft.
| 5. INSTALL 1ST GEAR |
![]() |
Coat the 1st gear with gear oil, and install it to the output shaft.
| 6. INSTALL NO. 1 TRANSAXLE CLUTCH HUB |
![]() |
Using SST and a press, press in the No. 1 transaxle clutch hub to the output shaft.
| 7. INSTALL 2ND GEAR BUSH BALL |
![]() |
Coat the bush ball with MP grease, and install it to the output shaft.
| 8. INSTALL 2ND GEAR BUSH |
![]() |
Coat the bush with gear oil, and install it to the output shaft.
| 9. INSTALL 2ND GEAR BEARING SPACER |
![]() |
Coat the bearing spacer with gear oil, and install it to the output shaft.
| 10. INSTALL 2ND GEAR NEEDLE ROLLER BEARING |
![]() |
Coat the needle roller bearing with gear oil, and install it to the output shaft.
| 11. INSTALL NO. 2 SYNCHRONIZER RING SET |
![]() |
Coat the No. 2 synchronizer ring set with gear oil, and install it to the No. 1 transaxle clutch hub.
| 12. INSTALL 2ND GEAR |
![]() |
Coat the 2nd gear with gear oil, and install it to the output shaft.
| 13. INSTALL 3RD DRIVEN GEAR |
![]() |
Using SST and a press, press in the 3rd driven gear to the output shaft.
| 14. INSTALL OUTPUT GEAR SPACER |
![]() |
Install the output gear spacer to the output shaft.
| 15. INSTALL 4TH DRIVEN GEAR |
![]() |
Using SST and a press, press in the 4th driven gear to the output shaft.
| 16. INSTALL FRONT OUTPUT SHAFT BEARING |
![]() |
Using SST and a press, press in the front bearing (inner race) to the output shaft.
| 17. INSPECT 2ND GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance.
| Bearing | Specified Condition |
| KOYO made | 0.009 to 0.053 mm (0.0004 to 0.0021 in.) |
| NSK made | 0.009 to 0.051 mm (0.0004 to 0.0020 in.) |
| 18. INSPECT 1ST GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance.
| Bearing | Specified Condition |
| KOYO made | 0.009 to 0.053 mm (0.0004 to 0.0021 in.) |
| NSK made | 0.009 to 0.051 mm (0.0004 to 0.0020 in.) |
| 19. INSPECT 2ND GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance.
| 20. INSPECT 1ST GEAR THRUST CLEARANCE |
![]() |
Using a feeler gauge, measure the thrust clearance.