Home › TRANSMISSION ยท E352 MANUAL TRANSAXLE › INPUT SHAFT

INPUT SHAFT > DISASSEMBLY

for Preparation Click here



1. INSPECT 4TH GEAR THRUST CLEARANCE


C069546E01
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.57 mm (0.0039 to 0.0224 in.)

    If the clearance is out of the specification, replace the No. 2 transaxle clutch hub, 4th gear or input shaft rear radial ball bearing.



2. INSPECT 3RD GEAR THRUST CLEARANCE


C069637E01
  1. Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)

    If the clearance is out of the specification, replace the No. 2 transaxle clutch hub, 3rd gear or input shaft.



3. INSPECT 4TH GEAR RADIAL CLEARANCE


C069548E01
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    Bearing
    Specified Condition
    KOYO made
    0.009 to 0.053 mm (0.0004 to 0.0021 in.)
    NSK made
    0.009 to 0.051mm (0.0004 to 0.0020 in.)

    If the clearance is out of the specification, replace the 4th gear, needle roller bearing or input shaft.



4. INSPECT 3RD GEAR RADIAL CLEARANCE


C069549E01
  1. Using a dial indicator, measure the gear radial clearance.

    Standard clearance:
    Bearing
    Specified Condition
    KOYO made
    0.009 to 0.053 mm (0.0004 to 0.0021 in.)
    NSK made
    0.009 to 0.051mm (0.0004 to 0.0020 in.)

    If the clearance is out of the specification, replace the 3rd gear, needle roller bearing or input shaft.



5. REMOVE 4TH GEAR


C070515E01
  1. Hold the input shaft assembly in a vise with soft jaws.

  1. Using 2 screwdrivers and a hammer, tap out the input shaft rear bearing shaft snap ring from the input shaft.

    HINT:
    Cover with a shop rag to keep the snap ring from flying off.



    C092867E01
  1. Using SST and a press, press out the input shaft rear bearing and 4th gear.

    SST
    09950-00020  

    NOTICE:
    Do not overtighten the SST.



6. REMOVE 4TH GEAR NEEDLE ROLLER BEARING


C069551E01
  1. Remove the needle roller bearing from the input shaft.



7. REMOVE 2ND SYNCHRONIZER OUTER RING


D031907E01
  1. Remove the 2nd synchronizer outer ring (No. 4 synchronizer ring) from the No. 2 transaxle clutch hub.



8. REMOVE 4TH GEAR BUSH


D031906E01
  1. Remove the 4th gear bush from the No. 2 transaxle clutch hub.



9. REMOVE 3RD GEAR


C069615E01
  1. Using 2 screwdrivers and a hammer, tap out the No. 2 clutch hub setting shaft snap ring from the input shaft.

    HINT:
    Cover with a shop rag to keep the snap ring from flying off.



    D031908E01
  1. Using SST and a press, press out the No. 2 transaxle clutch hub and 3rd gear from the input shaft.

    SST
    09950-00020  

    NOTICE:
    Do not overtighten the SST.



10. REMOVE 3RD GEAR NEEDLE ROLLER BEARING


C069617E01
  1. Remove the needle roller bearing from the input shaft.



11. REMOVE NO. 3 SYNCHRONIZER RING


C069618E01
  1. Remove the No. 3 synchronizer ring from the 3rd gear.



12. REMOVE NO. 2 TRANSAXLE HUB SLEEVE


C069619E01
  1. Remove the No. 2 transaxle hub sleeve, 3 No. 2 synchromesh shifting keys and 3 No. 2 synchromesh shifting key springs from the No. 2 transaxle clutch hub.

    HINT:
    Cover with a shop rag to keep the shifting key and shifting key spring from flying off.



13. REMOVE INPUT SHAFT FRONT BEARING


C092869E01
  1. Using SST and a press, press out the input shaft front bearing (inner race) from the input shaft.

    NOTICE:
    Do not overtighten SST.